- 您現在的位置：買賣IC網 > PDF目錄385928 > TLC075CPWPRG4 (Texas Instruments, Inc.) FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY OPERATIONAL AMPLIFIERS PDF資料下載
參數資料
| 型號： | TLC075CPWPRG4 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY OPERATIONAL AMPLIFIERS |
| 中文描述： | 家庭具有寬帶高輸出驅動單電源運算放大器 |
| 文件頁數： | 23/48頁 |
| 文件大?。?/td> | 1839K |
| 代理商： | TLC075CPWPRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SLOS219E JUNE 1999 REVISED SEPTEMBER 2006
23
WWW.TI.COM
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
APPLICATION INFORMATION
Although there are many ways to properly heatsink the PowerPAD package, the following steps illustrate the
recommended approach.
general PowerPAD design considerations (continued)
1.
The thermal pad must be connected to the same voltage potential as the GND pin.
2.
Prepare the PCB with a top side etch pattern as illustrated in the thermal land pattern mechanical drawing
at the end of this document. There should be etch for the leads as well as etch for the thermal pad.
3.
Place five holes (single and dual) or nine holes (quad) in the area of the thermal pad. These holes should
be 13 mils in diameter. Keep them small so that solder wicking through the holes is not a problem during
reflow.
4.
Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps
dissipate the heat generated by the TLC07x IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad
area to be soldered so that wicking is not a problem.
5.
Connect all holes to the internal ground plane that is the same potential as the device GND pin.
6.
When connecting these holes to the ground plane, do
not use the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the TLC07x PowerPAD package should make their connection to the internal ground plane
with a complete connection around the entire circumference of the plated-through hole.
7.
The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes (dual) or nine holes (quad) exposed. The bottom-side solder mask should cover the five or nine holes
of the thermal pad area. This prevents solder from being pulled away from the thermal pad area during the
reflow process.
8.
Apply solder paste to the exposed thermal pad area and all of the IC terminals.
9.
With these preparatory steps in place, the TLC07x IC is simply placed in position and run through the solder
reflow operation as any standard surface-mount component. This results in a part that is properly installed.
For a given
θ
JA
, the maximum power dissipation is shown in Figure 54 and is calculated by the following formula:
PD
TMAX–TA
JA
Where:
P
D
T
MAX
= Absolute maximum junction temperature (150
°
C)
T
A
= Free-ambient air temperature (
°
C)
θ
JA
=
θ
JC
+
θ
CA
θ
JC
= Thermal coefficient from junction to case
θ
CA
= Thermal coefficient from case to ambient air (
°
C/W)
= Maximum power dissipation of TLC07x IC (watts)
相關PDF資料 |
PDF描述 |
|---|---|
| TLC075IPWPRG4 | FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY OPERATIONAL AMPLIFIERS |
| TLC0820A(中文) | Advanced LinCMOS 8-Bit Analog-To-Digital Converters(8位高速A/D轉換器(帶改進的flash)) |
| TLC0831(中文) | 8-Bit Successive-Approximation Analog-To-Digital Converters(單輸入通道，串行I/O接口8位A/D轉換器) |
| TLC0832(中文) | 8-Bit Successive-Approximation Analog-To-Digital Converters(多重雙輸入通道，串行I/O接口8位A/D轉換器) |
| TLC0834(中文) | 8-Bit Successive-Approximation Analog-To-Digital Converters(4通道，串行I/O接口8位A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC075ID | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TLC075IDG4 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY OPERATIONAL AMPLIFIERS |
| TLC075IDR | 功能描述:運算放大器 - 運放 Quad Wide-Bandwidth Hi-Output-Drive RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TLC075IDRG4 | 功能描述:運算放大器 - 運放 Quad Wide Bandwidth Op Amp w/Shutdown RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TLC075IN | 功能描述:運算放大器 - 運放 Quad R/R RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。