參數資料
型號： TK63022BCB-G
廠商： TOKO INC
元件分類： 固定正電壓單路輸出LDO穩壓器
英文描述： 2.2 V FIXED POSITIVE LDO REGULATOR, 0.262 V DROPOUT, PBGA4
封裝： FC-4
文件頁數： 20/29頁
文件大小： 525K
代理商： TK63022BCB-G
TK630xxB
GC3-J013
Page 27
12-5. Definition of term
Characteristics
Output Voltage (V
Out)
The output voltage is specified with V
In=(VOutTYP+1V)
and I
Out=5mA.
Maximum Output Current (I
Out, MAX)
The rated output current is specified under the condition
where the output voltage drops 0.9V times the value
specified with I
Out=5mA.
The input voltage is set to
V
OutTYP+1V
and the current is pulsed to minimize
temperature effect.
Dropout Voltage (V
Drop)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the
regulator starts to fall out of regulation. Below this value,
the output voltage will fall as the input voltage is reduced.
It is dependent upon the output voltage, the load current,
and the junction temperature.
Line Regulation (LinReg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
from V
In=VOut,TYP+1V to VIn=VOut,TYP+6V. It is a pulse
measurement to minimize temperature effect.
Load Regulation (LoaReg)
Load regulation is the ability of the regulator to maintain
a constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects
with the input voltage set to V
In=VOut,TYP+1V. The load
regulation is specified under an output current step
condition of 5mA to 100mA.
Ripple Rejection (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 500mV
rms,
1kHz super-imposed on the
input voltage, where V
In=VOut,TYP+1.5V. Ripple rejection
is the ratio of the ripple content of the output vs. input and
is expressed in dB.
Standby Current (I
Standby)
Standby current is the current which flows into the
regulator when the output is turned off by the control
function (V
Cont=0V).
Protections
Over Current Sensor
The over current sensor protects the device when there is
excessive output current. It also protects the device if the
output is accidentally connected to ground.
Thermal Sensor
The thermal sensor protects the device in case the
junction temperature exceeds the safe value (T
j=150°C).
This temperature rise can be caused by external heat,
excessive power dissipation caused by large input to
output voltage drops, or excessive output current. The
regulator will shut off when the temperature exceeds the
safe value. As the junction temperatures decrease, the
regulator will begin to operate again. Under sustained
fault conditions, the regulator output will oscillate as the
device turns off then resets. Damage may occur to the
device under extreme fault.
Please prevent the loss of the regulator when this
protection operates, by reducing the input voltage or
providing better heat efficiency.
ESD
MM : 200pF 0
150V or more
HBM : 100pF 1.5k
2000V or more
相關PDF資料
PDF描述
TK63135SCL 3.5 V FIXED POSITIVE LDO REGULATOR, 0.42 V DROPOUT, PDSO5
TK70403MTR 1.03 V FIXED POSITIVE REGULATOR, PDSO6
TK71133NTR 3.25 V FIXED POSITIVE REGULATOR, PBCY3
TK71118N 1.75 V FIXED POSITIVE REGULATOR, PBCY3
TK71118NTR 1.75 V FIXED POSITIVE REGULATOR, PBCY3
相關代理商/技術參數
參數描述
TK630STL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:CMOS LDO REGULATOR WITH HIGH ACTIVE CONTROL ADVANCED
TK633 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low TC Precision Radial-Lead Film Resistors
TK633STL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:CMOS LDO REGULATOR WITH HIGH ACTIVE CONTROL ADVANCED
TK633V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low TC Precision Radial-Lead Film Resistors
TK634 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low TC Precision Radial-Lead Film Resistors
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*