參數資料
型號: TK11633UTL
廠商: TOKO INC
元件分類: 基準電壓源/電流源
英文描述: THREE-TERMINAL VOLTAGE REGULATOR
中文描述: 3.3 V FIXED POSITIVE LDO REGULATOR, 0.33 V DROPOUT, PSSO3
封裝: SOT-89, 3 PIN
文件頁數: 12/14頁
文件大?。?/td> 78K
代理商: TK11633UTL
Page 12
December 1998 TOKO, Inc.
TK116xxU
BOARD LAYOUT
Copper pattern should be as large as possible. Power
dissipation is 1000 mW for SOT-89. A low ESR capacitor
is recommended. For low temperature operation, select a
capacitor with a low ESR at the lowest operating
temperature to prevent oscillation, degradation of ripple
rejection and increase in noise. The minimum
recommended capacitance is 2.2
μ
F.
SOT-89 BOARD LAYOUT
APPLICATION INFORMATION
INPUT/OUTPUT
CONSIDERATIONS
DECOUPLING
CAPACITOR
Voltage regulators require input and output decoupling
capacitors. The required value of these capacitors vary
with application. Capacitors made by different
manufacturers can have different characteristics,
particularly with regard to high frequencies and Equivalent
Series Resistance (ESR) over temperature. The type of
capacitor is also important. For example, a 4.7
μ
F aluminum
electrolytic may be required for a certain application. If a
tantalum capacitor is used, a lower value of 2.2
μ
F would
be adequate. It is important to consider the temperature
characteristics of the decoupling capacitors. While Toko
regulators are designed to operate as low as -30
°
C, many
capacitors will not operate properly at this temperature.
The capacitance of aluminum electrolytic capacitors may
decrease to 0 at low temperatures. This may cause
oscillation on the output of the regulator since some
capacitance is required to guarantee stability. Thus, it is
important to consider the characteristics of the capacitor
over temperature when selection decoupling capacitors.
The ESR is another important parameter. The ESR will
increase with temperature but low ESR capacitors are
often larger and more costly. In general, tantalum capacitors
offer lower ESR than aluminum electrolytic, but new low
ESR aluminum electrolytic capacitors are now available
from several manufacturers. Usually a bench test is
sufficient to determine the minimum capacitance required
for a particular application. After taking thermal
characteristics and tolerance into account, the minimum
capacitance value should be approximately two times this
value. Please note that linear regulators with a low dropout
voltage have high internal loop gains which require care in
guarding against oscillation caused by insufficient
decoupling capacitance. The use of high quality decoupling
capacitors suited for your application will guarantee proper
operation of the circuit.
+
VOUT
+
VIN
GND
相關PDF資料
PDF描述
TK11806 DC-DC CONVERTER
TK11806M DC-DC CONVERTER
TK11806MBX DC-DC CONVERTER
TK11806MMG DC-DC CONVERTER
TK11806MTL DC-DC CONVERTER
相關代理商/技術參數
參數描述
TK116A 制造商:Thomas & Betts 功能描述:2" Compression Coupling, Steel-Zinc Plated, Concrete tight. For use with EMT Con 制造商:Thomas & Betts 功能描述:Fittings Coupler 2inch Steel
TK116A-RT 制造商:Thomas & Betts 功能描述:Fittings Coupler 2inch Steel
TK117A 制造商:Thomas & Betts 功能描述:2 1/2" COUPLING,COMP.,EMT,STL 制造商:Thomas & Betts 功能描述:Fittings Coupler 2.5inch Steel
TK117A-RT 制造商:Thomas & Betts 功能描述:2 1/2 IN RAINTIGHT COMPRESSION CPL
TK118A 制造商:Thomas & Betts 功能描述:Fittings Coupler 3inch Steel