- 您現在的位置：買賣IC網 > PDF目錄361481 > TK11633UTL (TOKO INC) THREE-TERMINAL VOLTAGE REGULATOR PDF資料下載
參數資料
| 型號： | TK11633UTL |
| 廠商： | TOKO INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | THREE-TERMINAL VOLTAGE REGULATOR |
| 中文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.33 V DROPOUT, PSSO3 |
| 封裝： | SOT-89, 3 PIN |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 78K |
| 代理商： | TK11633UTL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
Page 10
December 1998 TOKO, Inc.
TK116xxU
PACKAGE POWER DISSIPATION (P
D
)
This is the power dissipation level at which the thermal
sensor is activated. The IC contains an internal thermal
sensor which monitors the junction temperature. When
the junction temperature exceeds the monitor threshold of
150
°
C, the IC is shut down. The junction temperature
rises as the difference between the input power (V
IN
x I
IN
)
and the output power (V
OUT
x I
OUT
) increases. The rate of
temperature is greatly affected by the mounting pad
configuration on the PCB, the board material and the
ambient temperature. When the IC mounting has good
thermal conductivity, the junction temperature will be low,
even if the power dissipation is great. When the radiation
of heat is good, the device temperature will be low, even if
the power loss is great. When mounted on the
recommended mounting pad, the power dissipation of the
SOT-89 package is 1000 mW. Derate the power dissipation
at 8 mW/
°
C for operation above 25
°
C. To determine the
power dissipation for shutdown when mounted, attach the
device on the actual PCB and deliberately increase the
output current (or raise the input voltage) until the thermal
protection circuit is activated. Calculate the power
dissipation of the device by subtracting the output power
from the input power. The measurements should allow for
the ambient temperature of the PCB. The value obtained
from P
D
/(150
°
C - T
A
) is the derating factor. The PCB
mounting pad should provide maximum thermal
conductivity in order to maintain low device temperatures.
As a general rule, the lower the temperature, the better the
reliability of the device. The thermal resistance when
mounted is expressed as follows:
T
j
=
Θ
jA
x P
D
+ T
A
For Toko ICs, the internal limit for junction temperature is
150
°
C. If the ambient temperature (T
A
) is 25
°
C, then:
150
°
C =
Θ
jA
x P
D
+ 25
°
C
Θ
jA
= 125
°
C/P
D
P
D
is the value when the thermal sensor is activated. A
simple way to determine P
D
is to calculate V
IN
x I
IN
when
the output side is shorted. Input current gradually falls as
temperature rises. You should use the value when the
DEFINITION AND EXPLANATION OF TECHNICAL TERMS
LINE REGULATION (Line Reg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
from V
IN
= V
OUT(TYP)
+ 1 V to V
IN
= V
OUT(TYP)
+ 6 V.
LOAD REGULATION (Load Reg)
Load regulation is the ability of the regulator to maintain a
constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects
with the input voltage set to V
IN
= V
OUT(TYP)
+1 V. The load
regulation is specified under three output current step
conditions of 0 mA to 30 mA, 0 mA to 100 mA and 0 mA to
150 mA.
DROPOUT VOLTAGE (V
DROP
)
This is a measure of how well the regulator performs as the
input voltage decreases. The smaller the number, the
further the input voltage can decrease before regulation
problems occur. Nominal output voltage is first measured
when V
IN
= V
OUT(TYP)
+ 1 V at a chosen load current. When
the output voltage has dropped 100 mV from the nominal,
V
IN
- V
OUT
is the dropout voltage. This voltage is affected
by load current and junction temperature.
GROUND CURRENT (I
GND
)
Ground current is the current which flows through the
ground pin(s). It is defined as I
IN
- I
OUT
, excluding control
current.
OUTPUT NOISE VOLTAGE
This is the effective AC voltage that occurs on the output
voltage under the condition where the input noise is low
and with a given load, filter capacitor, and frequency
range.
THERMAL PROTECTION
This is an internal feature which turns the regulator off
when the junction temperature rises above 150
°
C. After
the regulator turns off, the temperature drops and the
regulator output turns back on. Under certain conditions,
the output waveform may appear to be an oscillation as the
output turns off and on and back again in succession.
相關PDF資料 |
PDF描述 |
|---|---|
| TK11806 | DC-DC CONVERTER |
| TK11806M | DC-DC CONVERTER |
| TK11806MBX | DC-DC CONVERTER |
| TK11806MMG | DC-DC CONVERTER |
| TK11806MTL | DC-DC CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TK116A | 制造商:Thomas & Betts 功能描述:2" Compression Coupling, Steel-Zinc Plated, Concrete tight. For use with EMT Con 制造商:Thomas & Betts 功能描述:Fittings Coupler 2inch Steel |
| TK116A-RT | 制造商:Thomas & Betts 功能描述:Fittings Coupler 2inch Steel |
| TK117A | 制造商:Thomas & Betts 功能描述:2 1/2" COUPLING,COMP.,EMT,STL 制造商:Thomas & Betts 功能描述:Fittings Coupler 2.5inch Steel |
| TK117A-RT | 制造商:Thomas & Betts 功能描述:2 1/2 IN RAINTIGHT COMPRESSION CPL |
| TK118A | 制造商:Thomas & Betts 功能描述:Fittings Coupler 3inch Steel |
發布緊急采購，3分鐘左右您將得到回復。