- 您現在的位置：買賣IC網 > PDF目錄382587 > THS6022EVM (Texas Instruments, Inc.) 250-mA DUAL DIFFERENTIAL LINE DRIVER PDF資料下載
參數資料
| 型號： | THS6022EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 250-mA DUAL DIFFERENTIAL LINE DRIVER |
| 中文描述： | 250毫安雙差分線路驅動器 |
| 文件頁數： | 28/38頁 |
| 文件大?。?/td> | 646K |
| 代理商： | THS6022EVM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
THS6022
250-mA DUAL DIFFERENTIAL LINE DRIVER
SLOS225C – SEPTEMBER 1998 – REVISED JANUARY 2000
28
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
driving a capacitive load
Driving capacitive loads with high performance amplifiers is not a problem as long as certain precautions are
taken. The first is to realize that the THS6022 has been internally compensated to maximize its bandwidth and
slew rate performance. When the amplifier is compensated in this manner, capacitive loading directly on the
output will decrease the device’s phase margin leading to high frequency ringing or oscillations. Therefore, for
capacitive loads of greater than 10 pF, it is recommended that a resistor be placed in series with the output of
the amplifier, as shown in Figure 55. A minimum value of 15
should work well for most applications. For
example, in 75-
transmission systems, setting the series resistor value to 75
both isolates any capacitance
loading and provides the proper line impedance matching at the source end.
+
_
THS6022
CLOAD
1 k
Input
Output
1 k
15
Figure 55. Driving a Capacitive Load
PCB design considerations
Proper PCB design techniques in two areas are important to assure proper operation of the THS6022. These
areas are high-speed layout techniques and thermal-management techniques. Because the THS6022 is a
high-speed part, the following guidelines are recommended.
Ground plane – It is essential that a ground plane be used on the board to provide all components with a
low inductive ground connection. Although a ground connection directly to a terminal of the THS6022 is not
necessarily required, it is recommended that the thermal pad of the package be tied to ground. This serves
two functions. It provides a low inductive ground to the device substrate to minimize internal crosstalk and
it provides the path for heat removal.
Input stray capacitance – To minimize potential problems with amplifier oscillation, the capacitance at the
inverting input of the amplifiers must be kept to a minimum. To do this, PCB trace runs to the inverting input
must be as short as possible, the ground plane must be removed under any etch runs connected to the
inverting input, and external components should be placed as close as possible to the inverting input. This
is especially true in the noninverting configuration. An example of this can be seen in Figure 56, which shows
what happens when a 1.0 pF capacitor is added to the inverting input terminal in the noninverting
configuration. The bandwidth increases dramatically at the expense of peaking. This is because some of
the error current is flowing through the stray capacitor instead of the inverting node of the amplifier. While
the device is in the inverting mode, stray capacitance at the inverting input has a minimal effect. This is
because the inverting node is at a virtual ground and the voltage does not fluctuate nearly as much as in
the noninverting configuration. This can be seen in Figure 57, where a 27-pF capacitor adds only 0.5 dB
of peaking. In general, as the gain of the system increases, the output peaking due to this capacitor
decreases. While this can initally appear to be a faster and better system, overshoot and ringing are more
likely to occur under fast transient conditions. So, proper analysis of adding a capacitor to the inverting input
node should always be performed for stable operation.
相關PDF資料 |
PDF描述 |
|---|---|
| THS6022IGQE | SLIM MOX, SM-102 , 47 MEG, 5%, ROHS |
| THS6022PWP | 250-mA DUAL DIFFERENTIAL LINE DRIVER |
| THS6022CGQE | 250-mA DUAL DIFFERENTIAL LINE DRIVER |
| THS6032GQE | LOW-POWER ADSL CENTRAL-OFFICE LINE DRIVER |
| THS6032DWP | LOW-POWER ADSL CENTRAL-OFFICE LINE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS6022GQE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:250-mA DUAL DIFFERENTIAL LINE DRIVER |
| THS6022IGQE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:250-mA DUAL DIFFERENTIAL LINE DRIVER |
| THS6022IPWP | 功能描述:高速運算放大器 250-mA Dual Diff Line Driver RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS6022IPWP | 制造商:Texas Instruments 功能描述:DIFF LINE DRIVER 6022 HTSSOP14 |
| THS6022IPWPG4 | 功能描述:高速運算放大器 250-mA Dual Diff Line Driver RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。