參數資料
型號： THS6012CGQE
廠商： Texas Instruments, Inc.
英文描述： 500-mA DUAL DIFFERENTIAL LINE DRIVER
中文描述： 500毫安雙差分線路驅動器
文件頁數： 26/35頁
文件大?。?/td> 604K
代理商： THS6012CGQE
THS6012
500-mA DUAL DIFFERENTIAL LINE DRIVER
SLOS226C– SEPTEMBER 1998 – REVISED FEBRUARY 2000
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
PCB design considerations (continued)
f – Frequency – Hz
N
100
1M
10M
100M
500M
–1
–3
–5
–7
–2
–4
–6
3
1
2
0
NORMALIZED FREQUENCY RESPONSE
vs
FREQUENCY
VCC =
±
15 V
VI = 200 mV
RL = 25
RF = 1 k
Gain = 1
CI = 0 pF
(Stray C Only)
CI = 1.8 pF
+
–
1 k
50
RL =
25
Cin
Vin
Vout
Figure 44. Driver Normalized Frequency Response vs Frequency
Proper power supply decoupling – Use a minimum of a 6.8-
μ
F tantalum capacitor in parallel with a 0.1-
μ
F
ceramic capacitor on each supply terminal. It may be possible to share the tantalum among several
amplifiers depending on the application, but a 0.1-
μ
F ceramic capacitor should always be used on the
supply terminal of every amplifier. In addition, the 0.1-
μ
F capacitor should be placed as close as possible
to the supply terminal. As this distance increases, the inductance in the connecting etch makes the capacitor
less effective. The designer should strive for distances of less than 0.1 inches between the device power
terminal and the ceramic capacitors.
Because of its power dissipation, proper thermal management of the THS6012 is required. Although there are
many ways to properly heatsink this device, the following steps illustrate one recommended approach for a
multilayer PCB with an internal ground plane.
1.
Prepare the PCB with a top side etch pattern as shown in Figure 45. There should be etch for the leads as
well as etch for the thermal pad.
2.
Place 18 holes in the area of the thermal pad. These holes should be 13 mils in diameter. They are kept
small so that solder wicking through the holes is not a problem during reflow.
3.
It is recommended, but not required, to place six more holes under the package, but outside the thermal
pad area. These holes are 25 mils in diameter. They may be larger because they are not in the area to be
soldered so that wicking is not a problem.
4.
Connect all 24 holes, the 18 within the thermal pad area and the 6 outside the pad area, to the internal
ground plane.
相關PDF資料
PDF描述
THS6022GQE 250-mA DUAL DIFFERENTIAL LINE DRIVER
THS6022EVM 250-mA DUAL DIFFERENTIAL LINE DRIVER
THS6022IGQE SLIM MOX, SM-102 , 47 MEG, 5%, ROHS
THS6022PWP 250-mA DUAL DIFFERENTIAL LINE DRIVER
THS6022CGQE 250-mA DUAL DIFFERENTIAL LINE DRIVER
相關代理商/技術參數
參數描述
THS6012DWP 制造商:TI 制造商全稱:Texas Instruments 功能描述:500-mA DUAL DIFFERENTIAL LINE DRIVER
THS6012EVM 功能描述:其他開發工具 THS6012 Hi-Spd Amp Eval Mods RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓:
THS6012GQE 制造商:TI 制造商全稱:Texas Instruments 功能描述:500-mA DUAL DIFFERENTIAL LINE DRIVER
THS6012IDWP 功能描述:緩沖器和線路驅動器 500-mA Dual Diff Line Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
THS6012IDWPG4 功能描述:緩沖器和線路驅動器 500mA Dual Diff Line Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*