- 您現在的位置：買賣IC網 > PDF目錄382581 > TEA5768HL (NXP SEMICONDUCTORS) Low-power FM stereo radio for handheld applications PDF資料下載
參數資料
| 型號： | TEA5768HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 接收器 |
| 英文描述： | Low-power FM stereo radio for handheld applications |
| 中文描述： | FM, AUDIO SINGLE CHIP RECEIVER, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-358-1, LQFP-32 |
| 文件頁數： | 8/36頁 |
| 文件大?。?/td> | 196K |
| 代理商： | TEA5768HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
2004 Sep 13
8
Philips Semiconductors
Product specification
Low-power FM stereo radio for
handheld applications
TEA5768HL
7.7
IF filter
Fully integrated IF filter.
7.8
FM demodulator
The FM quadrature demodulator has an integrated
resonator to perform the phase shift of the IF signal.
7.9
Level voltage generator and analog-to-digital
converter
The FM IF analog level voltage is converted to 4 bits digital
data and output via the I
2
C-bus.
7.10
IF counter
The IF counter outputs a 7-bit count result via the I
2
C-bus.
7.11
Soft mute
The low-pass filtered level voltage drives the soft mute
attenuator at low RF input levels. The soft mute function
can be switched off via the I
2
C-bus.
7.12
MPX decoder
The PLL stereo decoder is adjustment-free. The stereo
decoder can be switched to mono via the I
2
C-bus.
7.13
Signal dependent mono to stereo blend
With a decreasing RF input level the MPX decoder blends
from stereo to mono to limit the output noise. The
continuous mono to stereo blend can also be programmed
via the I
2
C-bus to an RF level depending switched mono to
stereo transition. Stereo Noise Cancelling (SNC) can be
switched off via the I
2
C-bus.
7.14
Signal dependent AF response
The audio bandwidth will be reduced with a decreasing RF
input level. This function can be switched off via the
I
2
C-bus.
7.15
Software programmable ports
Two software programmable ports (open-collector) can be
addressed via the I
2
C-bus.
The port 1 (pin SWPORT1) function can be changed with
write data byte 4 bit 0 (see Table 13). Pin SWPORT1 is
then output for the ready flag of read byte 1.
8
I
2
C-BUS AND BUS-CONTROLLED FUNCTIONS
8.1
I
2
C-bus specification
InformationabouttheI
2
C-buscanbefoundinthebrochure
“The I
2
C-bus and how to use it”(order number
9398 393 40011).
The standard I
2
C-bus specification is expanded by the
following definitions.
IC address C0: 1100000.
Structure of the I
2
C-bus logic: slave transceiver.
Subaddresses are not used.
The maximum LOW-level input and the minimum
HIGH-level input are specified to 0.2V
CCD
and 0.45V
CCD
respectively.
The pin BUSMODE must be connected to ground.
Before any READ or WRITE operation the pin
BUSENABLE has to be HIGH for at least 10
μ
s.
Note
: The bus operates at a maximum clock frequency of
400 kHz. It is not allowed to connect the IC to a bus
operating at a higher clock rate.
8.1.1
D
ATA TRANSFER
Datasequence:address,byte 1,byte 2,byte 3,byte 4and
byte 5 (the data transfer has to be in this order). The
LSB = 0 of the address indicates a WRITE operation to the
TEA5768HL.
Bit 7 of each byte is considered as the MSB and has to be
transferred as the first bit of the byte.
The data becomes valid bitwise at the appropriate falling
edge of the clock. A STOP condition after any byte can
shorten transmission times.
When writing to the transceiver by using the STOP
condition before completion of the whole transfer:
The remaining bytes will contain the old information
If the transfer of a byte is not completed, the new bits will
be used, but a new tuning cycle will not be started.
The IC can be switched into a low current standby mode
with the standby bit; the bus is then still active. The
standby current can be reduced by deactivating the bus
interface (pin BUSENABLE LOW). If the bus interface is
deactivated (pin BUSENABLE LOW) without the standby
mode being programmed, the IC maintains normal
operation, but is isolated from the bus lines.
相關PDF資料 |
PDF描述 |
|---|---|
| TEA5768 | single-chip FM stereo radio |
| TEA6101 | R-78xx-1.0 Series - Innoline Regulated DC-DC Converters; Output Voltage (Vdc): 3.3V; Output Current (A): 1.0A; Features: Efficiency up to 97%,Non isolated, no need for heatsinks; Pin-out compatible with LM78XX Linears; Low profile( L*W*H=11.5*8.5*17.5mm); Wide input range.(4.75V ~ 34V); Short circuit protection, Thermal shutdown; Non standard outputs available as specials between 1.5V ~15V; Low ripple and noise; ?L? version with 90?? pins |
| TEA6101T | |
| TEA6310 | Transient Voltage Suppressor Diodes |
| TEA6320TD | Tone/Volume/Balance Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TEA5768HL/V2,157 | 功能描述:調諧器 LO-PWR FM STEREO RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| TEA5768HL2FE | 功能描述:IC FM STEREO LOW POWER 32LQFP RoHS:是 類別:RF/IF 和 RFID >> RF 接收器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 09/Jan/2012 標準包裝:50 系列:* 頻率:850MHz ~ 2.175GHz 靈敏度:- 數據傳輸率 - 最大:- 調制或協議:- 應用:* 電流 - 接收:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 特點:- 電源電壓:4.75 V ~ 5.25 V 工作溫度:0°C ~ 85°C 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| TEA5768HLBD | 功能描述:調諧器 LO-PWR FM STEREO RADIO RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| TEA5777 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power AM/FM stereo radio for handheld applications |
| TEA5777HL | 功能描述:調諧器 AM/FM STEREO RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。