- 您現在的位置：買賣IC網 > PDF目錄371184 > TEA1532 (NXP Semiconductors N.V.) GreenChip SMPS control IC PDF資料下載
參數資料
| 型號： | TEA1532 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | GreenChip SMPS control IC |
| 中文描述： | 綠色芯片開關電源控制IC |
| 文件頁數： | 23/27頁 |
| 文件大?。?/td> | 147K |
| 代理商： | TEA1532 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
9397 750 13113
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Preliminary data sheet
Rev. 01 — 28 May 2004
23 of 27
Philips Semiconductors
TEA1532
GreenChip
II SMPS control IC
–
for packages with a thickness
≥
2.5 mm
–
for packages with a thickness < 2.5 mm and a volume
≥
350 mm
3
so called
thick/large packages.
below 240
°
C (SnPb process) or below 260
°
C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
14.3.2
Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250
°
C or
265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
14.3.3
Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TEA1532P | GreenChip SMPS control IC |
| TEA1532T | GreenChip SMPS control IC |
| TEA1654 | GreenChipII SMPS control IC |
| TEA1654T | GreenChipII SMPS control IC |
| TEA5570 | RF/IF circuit for AM/FM radio |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TEA1532AP/N1,112 | 功能描述:開關變換器、穩壓器與控制器 GREENCHIP 2 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1532APN | 功能描述:開關變換器、穩壓器與控制器 GREENCHIP 2 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1532AT/N1,118 | 功能描述:開關變換器、穩壓器與控制器 GREENCHIP 2 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1532AT/N1/DG,11 | 功能描述:開關變換器、穩壓器與控制器 12V 170mA 63KHz RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1532AT/N1/DG,118 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
發布緊急采購，3分鐘左右您將得到回復。