參數資料
型號： TDA9818T
廠商： NXP SEMICONDUCTORS
元件分類： 接收器
英文描述： Single/multistandard VIF/SIF-PLL and FM-PLL/AM demodulators
中文描述： AM/FM, AUDIO/VIDEO DEMODULATOR, PDSO24
封裝： 7.50 MM, PLASTIC, SOT-137-1, MS-013, SOP-24
文件頁數： 37/41頁
文件大?。?/td> 240K
代理商： TDA9818T
2004 Jun 29
37
Philips Semiconductors
Product specification
Single/multistandard VIF/SIF-PLL and
FM-PLL/AM demodulators
TDA9817; TDA9818
SOLDERING
Introduction
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-holeandsurfacemountcomponentsaremixedon
one printed-circuit board. Wave soldering can still be used
for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is
recommended. Driven by legislation and environmental
forces the worldwide use of lead-free solder pastes is
increasing.
Through-hole mount packages
S
OLDERING BY DIPPING OR BY SOLDER WAVE
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250
°
C or 265
°
C, depending on solder
material applied, SnPb or Pb-free respectively.
Thetotalcontacttimeofsuccessivesolderwavesmustnot
exceed 5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
stg(max)
). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
M
ANUAL SOLDERING
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300
°
C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400
°
C, contact may be up to 5 seconds.
Surface mount packages
R
EFLOW SOLDERING
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270
°
C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
below 225
°
C (SnPb process) or below 245
°
C (Pb-free
process)
– for all the BGA, HTSSON..T and SSOP-T packages
– for packages with a thickness
≥
2.5 mm
– for packages with a thickness < 2.5 mm and a
volume
≥
350 mm
3
so called thick/large packages.
below 240
°
C (SnPb process) or below 260
°
C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
W
AVE SOLDERING
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
相關PDF資料
PDF描述
TDA9817TS Single/multistandard VIF/SIF-PLL and FM-PLL/AM demodulators
TDA9817T Single/multistandard VIF/SIF-PLL and FM-PLL/AM demodulators
TDA9818TS Single/multistandard VIF/SIF-PLL and FM-PLL/AM demodulators
TDA9819T Multistandard vision and sound-IF PLL with DVB-IF processing
TDA9819 Multistandard Vision And Sound-IF PLL With DVB-IF Processing(帶數字視頻廣播-中頻（DVB-IF）處理的多標準視覺及聲音-中頻（IF）的 PLL)
相關代理商/技術參數
參數描述
TDA9818T/V1,118 功能描述:IC FM-PLL/AM DEMOD 24-SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
TDA9818TS 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single/multistandard VIF/SIF-PLL and FM-PLL/AM demodulators
TDA9819 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard vision and sound-IF PLL with DVB-IF processing
TDA9819T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard vision and sound-IF PLL with DVB-IF processing
TDA9820 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard/dual channel TV FM intercarrier sound demodulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*