參數資料
型號： TDA9615
廠商： NXP Semiconductors N.V.
英文描述： DIODE,TVS,BI,20V,1500W,J-LEAD
中文描述： 音頻處理器錄影帶高保真
文件頁數： 12/44頁
文件大小： 263K
代理商： TDA9615
1997 Jun 16
12
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
3.
Modes ‘loop-through’ and ‘record’ are equal in audio signal flow; FMOUT (pin 36) however is muted during
‘loop-through’ mode.
POR.
4.
Table 7
Bit NTSC
Notes
1.
Bit NTSC selects between the system standard settings for NTSC and PAL (SECAM) use. The auto-calibration
function uses the system standard HID frequency of 29.97 Hz for NTSC and 25 Hz for PAL. After calibration bit NTSC
allows immediate switching between the NTSC and PAL system standard.
POR.
2.
Table 8
Bit MUTE
Notes
1.
Bit MUTE controls the line and RFC output mute switches at pins 13, 14 and 17 (power mute function). Power mute
is also automatically activated at supply voltage power-up or power-down (V
CC
; pin 35).
POR.
2.
Table 9
Bits STBP and STBA
Notes
1.
2.
POR.
By selecting STBA = 1 the TDA9615H is switched to low-power ‘a(chǎn)ctive standby’ mode. To reduce power
consumption most circuits are switched off. RFC, line and decoder outputs however remain active. This way the
direct audio selections offered via the line output select and decoder output select functions (bits LOS and DOS of
the output byte) remain operable in this mode. The ‘Output Select’ mode signal is muted.
Calibration and I
2
C-bus registers are not affected by using ‘a(chǎn)ctive standby’ or ‘passive standby’ mode.
By selecting STBP = 1 the TDA9615H is switched to minimum power ‘passive standby’ mode. All circuits except
power mute, I
2
C-bus and the line input reference buffer (voltage at pins 1 to 10 and 44) are switched off for minimum
power consumption. Use of the power mute function (bit MUTE of control byte) ensures pop-free switching of the line
and RFC output to and from ‘passive standby’ mode. To obtain minimum power consumption the power mute
function should be de-activated again during ‘passive standby’ mode.
X = don’t care.
3.
4.
5.
NTSC
(1)
MODE
DESCRIPTION
0
1
PAL
NTSC
(2)
hi-fi circuit in ‘PAL’ mode (FM carriers: 1.4 and 1.8 MHz)
hi-fi circuit in ‘NTSC’ mode (FM carriers: 1.3 and 1.7 MHz)
MUTE
(1)
MODE
DESCRIPTION
0
1
mute
(2)
power mute function released; mute switches open
power mute function activated; mute switches closed
STBP
STBA
MODE
DESCRIPTION
0
0
1
(4)
0
1
(2)
X
(5)
(note 1)
active standby
(3)
passive standby
(3)
full operation
standby mode; reduced power consumption
standby mode; minimum power consumption
相關PDF資料
PDF描述
TDA9615H Audio processor for VHS hi-fi(應用于VHS高保真的音頻處理器)
TDA9811 Multistandard VIF-PLL with QSS-IFand AM demodulator(帶QSS-IF和AM解調器的多標準的VIF-PLL)
TDA9812 Multistandard VIF-PLL andFM-PLL/AM demodulator(多標準的VIF-PLL 和FM-PLL/AM解調器)
TDA9812T Multistandard VIF-PLL and FM-PLL/AM demodulator
TDA9813T VIF-PLL with QSS-IF and dual FM-PLL demodulator(帶QSS-IF和雙路FM-PLL解調器的VIF-PLL)
相關代理商/技術參數
參數描述
TDA9615H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio processor for VHS hi-fi
TDA9725 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Y/C automatic adjustment processor VHS standard
TDA9800 制造商:NXP Semiconductors 功能描述:Video/TV Circuit, TV Video Receiver Circuit, 20 Pin, Plastic, DIP
TDA9800T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:VIF-PLL demodulator and FM-PLL detector
TDA9801 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single standard VIF-PLL demodulator and FM-PLL detector
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*