- 您現在的位置：買賣IC網 > PDF目錄371182 > TDA8591J (NXP SEMICONDUCTORS) 4 X 44 W into 4 or 4 X 75 W into 2 quad BTL car radio power amplifier PDF資料下載
參數資料
| 型號： | TDA8591J |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 4 X 44 W into 4 or 4 X 75 W into 2 quad BTL car radio power amplifier |
| 中文描述： | 47 W, 4 CHANNEL, AUDIO AMPLIFIER, PZFM27 |
| 封裝： | PLASTIC, DIL-BENT-SIL, 27 PIN |
| 文件頁數： | 11/36頁 |
| 文件大?。?/td> | 295K |
| 代理商： | TDA8591J |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
2002 Jan 14
11
Philips Semiconductors
Preliminary specification
4
×
44 W into 4
or 4
×
75 W into 2
quad BTL car radio power amplifier
TDA8591J
7.3
Mute timer and single-pin mute control
Thetransition time frommute modetooperating modecan
be used to hide plops that occur during switching. This
transition time is determined by the value of the external
capacitor at the MUTE/ON input (see Fig.33). To
guarantee the mute suppression, the resistor value may
not be more than 15 k
. The switching can be controlled
by a transistor switch with an open-drain output or a
voltage output with a minimum high level of 5.5 V.
When controlling with an open-drain output, the high
voltage level also must be at least 5.5 V and should not be
clamped on a lower value by the ESD diode of the
microcontroller. If the minimum high voltage cannot be
guaranteed, an external open-drain transistor or switch to
ground can be used. Charging of the external capacitor at
the MUTE/ON input is done by an internal current source.
If muting is performed by the microcontroller, the mute
connection to the microcontroller can be omitted. The
mute on and off transitions during start-up and switch-off
are controlled by an internal push-pull current source and
the external capacitor at pin 8 (MUTE/ON).
Fast mute can be achieved by quickly discharging the
mute capacitor by means of an open-drain transistor
without a series resistor.
7.4
Output power
EIAJpowerisapowerratingwhichindicatesthemaximum
possibleoutputpowerofaspecificapplicationatanominal
supply voltage. The power losses caused by PCB layout,
copper area, connector block, coil, loudspeaker wires, etc.
depend on the applications.
Therefore, the EIAJ power is defined and measured at the
pins of the IC using the following test conditions:
The supply voltage is 14.4 V measured on the pins of
the TDA8591J
All channels are loaded with 4
and are driven
simultaneously
The input signal is a continuous (no burst) square wave:
V = 1 V (RMS); f = 1 kHz
RMS output power is measured immediately at the start
(cold heatsink) and after 1 minute of operation. The
mean value is the rated EIAJ power.
To have optimum output power performance, the external
heatsink should be chosen carefully. A small heatsink
causes a high junction temperature, resulting in an
increase of the drain-source on-state resistance (R
DSon
) of
the power amplifiers and a decrease of the maximum
output power.
The reason for using a square wave input signal for EIAJ
power measurement is illustrated in Fig.9.
Figure 9a shows a square wave signal with
Assuming this square wave is the output signal of an
amplifier, the EIAJ output power is given by
where:
R
L
= load resistor in
V
top
= maximum voltage across the load in V
f = frequency of the square wave in Hz
t
r
= rise time of the slope in s.
A sine wave has a lower slew rate than a square wave as
shown in Fig.9b, therefore EIAJ power measurement with
a sine wave will give a lower power value. The maximum
slew rate of a sine wave output signal is given by
where:
A = amplitude of the output sinewave in V
f = frequency of the output sinewave in Hz.
For a non-clipping sinewave output with amplitude
A = 13 V and frequency f = 1 kHz, the slew rate is
A faster slew rate can be obtained by increasing the
amplitude: for an amplitude of 28 V, the slew rate will
increase to 1.8
5
V/s. A supply voltage of V
P
= 14.4 V will
result in a clipped output with a shape similar to a square
wave but with a slower slew rate.
Figure 9c shows the dependency of P
EIAJ
on slew rate.
Using a square wave input signal, the EIAJ output power
is determined by the drop voltage and bandwidth of the
output stage.
slew rate
V
t
r
---------
=
P
EIAJ
V
R
L
2
-------------
1
------------------------------------------
3
slew rate
V
top
×
f
×
–
×
=
δ
U
--t max
--- A
sin
δ
t max
×
2
π
f
t
×
(
)
)
2
π
f
A
×
=
=
δ
U
t max
-----------------
82
3
V/s
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8601 | RGB/YUV and fast blanking switch |
| TDA8601T | RGB/YUV and fast blanking switch |
| TDA8741 | satellite sound circuit with noise reduction |
| TDA8741H | Satellite sound circuit with noise reduction |
| TDA8757 | Triple 8-bit ADC 170 Msps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8591J/N1,112 | 功能描述:音頻放大器 4 X 44 W INTO 4 OHM OR 4 X 75 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8594 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled 4 X 50 W power amplifier |
| TDA8594J | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled 4 X 50 W power amplifier |
| TDA8594J/N1 | 功能描述:音頻放大器 AMPLIFIER 4X50W RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8594J/N1,112 | 制造商:NXP Semiconductors 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。