參數資料
型號： TDA8512J
廠商： NXP SEMICONDUCTORS
元件分類： 音頻／視頻放大
英文描述： 26 W BTL and 2 x 13 W SE or 4 x 13 W SE power amplifier
中文描述： 13 W, 4 CHANNEL, AUDIO AMPLIFIER, PZFM17
封裝： PLASTIC, DIL-BENT-SIL, 17 PIN
文件頁數： 11/24頁
文件大?。?/td> 165K
代理商： TDA8512J
2001 Nov 16
11
Philips Semiconductors
Preliminary specification
26 W BTL and 2
×
13 W SE or
4
×
13 W SE power amplifier
TDA8512J
14 APPLICATION INFORMATION
14.1
Input configuration
Inputs 1 and 2 are used for SE application on pin OUT1,
respectively pin OUT2
Input 3 can be configured for both SE and BTL
application
Input 4 can be used for SE application of pin OUT4, or
for BTL application together with input 3. See
Figs 6 and 7.
Note that the DC level of all input pins is half the supply
voltage V
P
, so coupling capacitors for the input pins are
necessary!
Cut-off frequency for the input is: f
i(co)
= 12 Hz. Therefore
it is not necessary to use high capacitor values on the
input;sothedelayduringswitch-on,whichisnecessaryfor
charging the input capacitors, can be minimised. This
results in a good low frequency response and good
switch-on behaviour.
14.2
Output power
The output power versus supply voltage has been
measured on the output pins of one channel, and at
THD = 10%. The maximum output power is limited by the
maximum supply voltage of 18 V and the maximum
available output current: 4 A repetitive peak current.
14.3
Power dissipation
The power dissipation graphs are given for one output
channel in SE, respectively BTL application. So for total
worst-case power dissipation the P
d
of each channel must
be added up.
14.4
Supply Voltage Ripple Rejection (SVRR)
The SVRR is measured with an electrolytic capacitor of
100
μ
F on pin RR and at a bandwidth of 10 Hz to 80 kHz,
whereas the lowest frequencies can be lower than 10 Hz.
Proper supply bypassing is critical for low noise
performance and high power supply rejection. The
respective capacitor locations should be as close to the
device as possible, and grounded to the power ground. A
properpowersupplydecouplingalsopreventsoscillations.
For suppressing higher frequency transients (spikes) on
the supply line a capacitor with low ESR (typical 0.1
μ
F)
has to be placed as close as possible to the device. For
suppressing lower frequency noise and ripple signals, a
large electrolytic capacitor (e.g.1000
μ
F or more) must be
placed close to the device.
Thebypass capacitoronthepin RRreduces thenoiseand
ripple on the mid rail voltage. For good THD and noise
performance, a low ESR capacitor is recommended.
14.5
Switch-on and switch-off
To avoid audible plops during switching on and switching
off the supply voltage, the pin MODE has to be set in
standby condition (<2V) before the voltage is applied
(switch-on) or removed (switch-off). Via the mute mode,
the input- and SVRR-capacitors are smoothly charged.
The turn-on and turn-off time can be influenced by an
RC-circuit on the pin MODE (see Fig.3). Rapidly switching
on and off of the device or the pin MODE, may cause “click
and pop” noise. This can be prevented by a proper timing
on the pin MODE.
14.6
PCB layout and grounding
For high system performance level certain grounding
techniques are imperative. The input reference grounds
have to be tied with their respective source grounds, and
must have separate traces from the power ground traces;
this will separate the large (output) signal currents from
interfering with the small AC input signals. The
small-signal ground traces should be physically located as
far as possible from the power ground traces. Supply- and
output-traces should be as wide as practical for delivering
maximum output power. The PCB layout, which
accommodates the TDA8510, TDA8511, and TDA8512
products, is shown in Fig.8.
相關PDF資料
PDF描述
TDA8540T 4 X 4 video switch matrix
TDA8540 4 X 4 video switch matrix
TDA8542AT 2 x 1.5 W BTL audio amplifier
TDA8542 2 x 1 W BTL audio amplifier
TDA8542T 2 x 1 W BTL audio amplifier
相關代理商/技術參數
參數描述
TDA8512J/N1,112 功能描述:音頻放大器 4X16W SE/BTL FLEX RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8512JU 功能描述:音頻放大器 4X16W SE/BTL FLEX CHANNEL AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8540 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 X 4 video switch matrix
TDA8540T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 X 4 video switch matrix
TDA8540TD-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Cross-Point Switch
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*