- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8031 (NXP Semiconductors N.V.) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8031 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | USB智能卡閱讀器（OTP或光盤） |
| 文件頁數： | 36/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8031 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
36
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.5.2
P
HASE
-
LOCKED LOOP
A 12 to 48 MHz clock multiplier PLL is integrated on-chip. No external components are needed for the operation of the
PLL.
8.5.3
B
IT CLOCK RECOVERY
The bit clock recovery circuit recovers the clock from the incoming USB data stream using 4
×
oversampling principle.
It is able to track jitter and frequency drift as specified by the USB specification.
8.5.4
I
NTERFACE SIGNALS WITH THE MICROCONTROLLER
Table 30
The following I/O ports of the 83C51 are used for controlling the USB bus:
8.5.5
B
LOCK DIAGRAM
The digital interface consists of 3 major blocks:
The Philips Serial Interface Engine (SIE) handles the USB protocol (i.e. synchronization pattern, recognition,
parallel/serial conversion, bit stuffing/de-stuffing, CRC checking/generating, PID verification/generation, address
recognition and handshake evaluation/generation)
A Memory Management Unit (MMU), controlling the buffering of data to and from the bus
An interface to the embedded 83C51 microcontroller.
PORT
FUNCTION
DESCRIPTION
P10
USB_INT_MASK
should be set to logic 1 before entering power-down mode during suspend
and reset to logic 0 when leaving power-down mode
when set to logic 1, the internal 1.5 k
resistor is connected to pin D+
the device is ready to accept a new transaction
when LOW, this signal indicates that the bus is no longer suspended
a LOW-level will reset the USB interface
when set to logic 1, V
DDD
is applied on the optional external 1.5 k
resistor
which has been placed between pins D+ and DELATT
interrupt to the microcontroller
the device is in suspended state (TDA8030 only)
remote wake-up (TDA8030 only)
if set to logic 1, the data to the bus is a command; if set to logic 0 it is data
if set to logic 1, the USB interface is selected
P11
P12
P13
P14
P15
USB_SOFTCONNECT_INT
USB_MC_READY
USB_CLK_EN_N
USB_RESET_N
USB_SOFTCONNECT_EXT
P33
P34
P35
P25
P26
USB_INT_N
USB_SUSPEND
USB_WAKEUP_N
USB_MP_C
USB_MP_SEL
handbook, full pagewidth
MGU891
ANALOG
TRANSCEIVER
SERIAL
INTERFACE
ENGINE
OSCILLATOR
RAM
MEMORY
MANAGEMENT
UNIT
MICRO-
CONTROLLER
INTERFACE
MICRO-
CONTROLLER
D
+
D
USB bus
Fig.11 USB block diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
| TEA1201TS | 0.95 V starting basic power unit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034AT/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。