- 您現在的位置：買賣IC網 > PDF目錄382581 > TDA8031 (NXP Semiconductors N.V.) USB smart card reader (OTP or ROM) PDF資料下載
參數資料
| 型號： | TDA8031 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | USB smart card reader (OTP or ROM) |
| 中文描述： | USB智能卡閱讀器（OTP或光盤） |
| 文件頁數： | 35/57頁 |
| 文件大?。?/td> | 228K |
| 代理商： | TDA8031 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
2003 Jul 04
35
Philips Semiconductors
Product specification
USB smart card reader (OTP or ROM)
TDA8030; TDA8031
8.4.1
L
OW POWER MODES
Stop Clock Mode: The static design enables the clock
speed to be reduced down to 0 MHz (stopped). When the
oscillator is stopped, the RAM and Special Function
Registers (SFRs) retain their values. This mode allows
step-by-steputilizationandpermitsreducedsystempower
consumption by lowering the clock frequency down to any
value. The power-down mode is suggested for the lowest
power consumption.
IDLE Mode: In the Idle mode, the CPU puts itself to sleep
while all of the on-chip peripherals stay active. The
instruction to invoke the Idle mode is the last instruction
executed in the normal operating mode before the Idle
mode is activated. The CPU contents, the on-chip RAM
andallofthespecialfunctionregistersremainintactduring
this mode. The Idle mode can be terminated either by any
enabled interrupt (at which time the process is picked up
at the interrupt service routine and continued), or by a
hardware reset which starts the processor in the same
manner as a Power-on reset.
Power-down Mode: To save even more power, a
power-down mode can be invoked by software. In this
mode, the oscillator is stopped and the instruction that
invoked the power-down is the last instruction executed.
Either a hardware reset or external interrupt can be used
to exit from the power-down mode. Applying a reset
redefines all of the SFRs but does not change the on-chip
RAM. An external interrupt allows both the SFRs and the
on-chip RAM to retain their values.
The bits in the Interface Engine (IE) must be enabled with
INT0 and INT1. Within the INT0 interrupt service routine,
the microcontroller has to read out the Hardware Status
Register (HSR at 0FH) and/or the UART Status register
(USR at 0EH) by means of MOVX instructions in order to
establish the exact interrupt reason and to reset the
interrupt source.
For enabling a wake-up by INT1, the bit ENINT1 within
UCR2 must be set.
An integrated delay counter maintains INT0 and INT1
LOWlong enoughtoallow theoscillatorto restartproperly.
A falling edge on pins INT0 and INT1 is enough to awaken
the whole circuit.
Once the interrupt is serviced, the next instruction to be
executed after RETI will be the one following the
instruction that put the device into power-down.
8.5
USB INTERFACE
8.5.1
E
ND
-
POINTS
The TDA8030; TDA8031 has 4 logic end-points which are
listed in Table 29.
Each physical end-point, except for the control ones, can
be enabled or disabled. All enabled end-points generate
interrupts to the microcontroller via INT1 when the
end-point needs to be serviced.
TheimplementationofthefunctionmakesuseofanSRAM
for buffering the data.
Logic end-points can be accessed by the microcontroller
interface.
Table 29
Mapping of logic to physical end-point numbers for used end-points
END-POINT NAME
LOGIC
END-POINT
BUFFER SIZE
PHYSICAL END-POINT
OUT
IN
Control end-point
Generic end-point (may be used as bulk
Generic end-point (may be used as interrupt)
Generic end-point
0
1
2
3
16
32
8
8
0
2
1
3
4
5
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8031HL | USB smart card reader (OTP or ROM) |
| TDA8302 | SMALL SIGNAL COMBINATION IC FOR COLOUR TV |
| TDA8931 | Power comparator 1 X 20 W |
| TDA8931T | Power comparator 1 X 20 W |
| TEA1201TS | 0.95 V starting basic power unit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8031HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB smart card reader (OTP or ROM) |
| TDA8034AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart card interface |
| TDA8034AT/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape |
| TDA8034AT/C1,112 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TDA8034AT/C1,118 | 功能描述:接口 - 專用 SMART CARD INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。