- 您現在的位置：買賣IC網 > PDF目錄385914 > TCM320AC37N (Texas Instruments, Inc.) VOICE-BAND AUDIO PROCESSORS VBAPE PDF資料下載
參數資料
| 型號： | TCM320AC37N |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | VOICE-BAND AUDIO PROCESSORS VBAPE |
| 中文描述： | 語音頻帶音頻處理器VBAPE |
| 文件頁數： | 13/23頁 |
| 文件大?。?/td> | 317K |
| 代理商： | TCM320AC37N |
TCM320AC36, TCM320AC37
VOICE-BAND AUDIO PROCESSORS (VBAP
)
SLWS003C – MAY 1992 – REVISED APRIL – 1998
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
general
system reliability features
The device should be powered up and initialized as follows:
1.
2.
3.
4.
5.
Apply GND.
Apply V
CC
.
Connect all clocks.
Apply TTL high to PDN.
Apply synchronizing pulses to FSX and/or FSR.
Even though the VBAP is heavily protected against latch-up, it is still possible to cause it to latch up under certain
improper power conditions. To help ensure that latch-up does not occur, a reverse-biased Schottky diode (with
a forward voltage drop of less than or equal to 0.4 V — 1N5711 or equivalent) should be connected between
V
CC
(power supply) and GND.
On the transmit channel, digital outputs DOUT and TSX are held in the high-impedance state for approximately
four frames (500
μ
s) after power up or application of V
CC
. After this delay, DOUT, TSX, and signaling are
functional and occur in the correct time slot. The analog circuits on the transmit side require approximately
60 ms to reach their equilibrium value due to the autozero circuit settling time. To further enhance system
integrity, DOUT and TSX are placed in the high-impedance state after an interruption of CLK.
power-down and standby operations
To minimize power consumption, a power-down mode and three standby modes are provided.
For power down, an external low signal is applied to PDN. In the absence of a signal, PDN is internally pulled
up to a high logic level and the device remains active. In the power-down mode, the average power consumption
is reduced to 3 mW.
Three standby modes give the user the option of placing the entire device on standby, placing only the transmit
channel on standby, or placing only the receive channel on standby. To place the entire device on standby, both
FSX and FSR are held low. For transmit-only operation (receive channel on standby), FSX is pulsing and FSR
is held low. For receive-only operation (transmit section on standby), FSR is pulsing and FSX is held low. When
the entire device is in standby mode, power consumption is reduced to 5 mW. See Table 1 for power-down and
standby procedures.
相關PDF資料 |
PDF描述 |
|---|---|
| TCM320AC37PT | VOICE-BAND AUDIO PROCESSORS VBAPE |
| TCM320AC54 | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TCM320AC54DW | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TCM320AC54N | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TCM809(中文) | 3-Pin Microcontroller Reset Monitors(3引腳微控制器復位監控器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TCM320AC37PT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VOICE-BAND AUDIO PROCESSORS VBAPE |
| TCM320AC38 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VOICE-BAND AUDIO PROCESSORS (VBAPE) |
| TCM320AC39CPT | 制造商:Texas Instruments 功能描述: |
| TCM320AC39IDW | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TCM320AC46 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:GEBERAL-PURPOSE AUDIO INTERFACE FOR DSP |
發布緊急采購，3分鐘左右您將得到回復。