2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
4
5
1
2
3
6
7
8
9
10
Vcc
Supply
Voltage
Voltage
Control
DNC
DNC DNC
DNC DNC
.01uF
Bypass
E/D
Output
10pF
10Kohm
Notes:
1)
TCXO: Initial calibration @ 25
C. Specifications at time of shipment after 48
hours of operation.
Inclusive of calibration @ 25
C, frequency vs. change in temperature, change in
supply voltage (±5%), load change (±5%), reflow soldering process and 20
years aging.
For best in applicationperformance, careful selection of an external power
source is critical. Select an external regulator that meets or exceeds to following
specifications regarding voltage regulation tolerance, initial accuracy,
temperature coefficient, voltage noise, and low voltage noise density.
Factory Test Conditions:
Initial Accuracy ±2mv, Noise (0.1Hz to 10 KHz) 15uV
p-p, Voltage Noise Density = 50nV/sqrtHz, Temperature Coefficient < 5ppm°C.
Leave Pad 8 unconnected if enable / disable function is not required. When tri-
stated, the output stage is disabled but the oscillator and compensation circuit
are still active (currentconsumption <1 mA).
Additional pull ranges are available; please contact the factory for additional
information.
Output is AC coupled.
Specifications subject to change without notice. All dimensions in inches. Copyright 2007 The Connor-Winfield Corporation
2)
3)
4)
5)
6)
Clipped Sinewave Test Circuit
Features
Electrical Specifications for all Models
OPERATING SPECIFICATIONS
PARAMETER
TCXO Frequency Calibration @ 25
C
Total Frequency Tolerance
Supply Voltage
Supply Current
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 20MHz)
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at >10KHz offset
SSB Phase Noise at >100KHz offset
Start Up Time
TCXO
VCTCXO
3.3V Operation
LVCMOS Output
Clipped Sinewave Output
Frequency Stability:
T50x/T60xSeries+/-0.28ppm
T51x/T61x-Series+/-0.50ppm
T52x/T62x-Series+/-1.00ppm
Temperature Range:
T5xx-Series 0 to 70°C
T6xx-Series -40 to 85°C
Low Jitter <1pS RMS
Tri-State Enable/Disable
Surface Mount Package
Tape and Reel Packing
RoHS Compliant / Lead Free
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Bulletin
Page
Revision
Date
Tx176
3 of 4
06
30 Aug 2007
Table 9.0
Notes
1
2
3
MINIMUM
-1.00
-4.60
3.135
-
-
-
-
-
-
-
-
-
NOMINAL MAXIMUM
-
-
3.3
6
-
-
-80
-110
-135
-150
-150
-
UNITS
ppm
ppm
Vdc
mA
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ms
1.00
4.60
3.465
10
5
1
-70
-100
-130
-145
-150
10
(Vcc)
(Icc)
INPUT CHARACTERISTICS for ENABLE / DISABLE FUNCTION (Pin 8)
PARAMETER
Enable Voltage (High) or open circuit
Disable Voltage (Low) Output Tri-stated
Table 10.0
Notes
4
MINIMUM
70% Vdd
-
NOMINAL MAXIMUM
-
-
UNITS
Vdc
Vdc
(Vih)
(Vil)
-
30% Vdd
INPUT CHARACTERISTICS for VOLTAGE CONTROL (Pin10)
PARAMETER
Control Voltage Range (Vcc = 3.3V)
Frequency Tuning
Linearity
Slope
Table 11.0
MINIMUM
0.3
±10
±5
Positive
NOMINAL MAXIMUM
1.65
-
-
UNITS
Vdc
ppm
%
Notes
(Vc)
3.0
-
-
5
LVCMOS OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Voltage (High)
(Low)
Current (High)
(Low)
Duty Cycle at 50% of Vcc
Rise / Fall Time10% to 90%
Table 12.0
MINIMUM
-
90%Vcc
-
-4
-
45
-
NOMINAL
-
-
-
-
-
50
-
MAXIMUM
15
-
10%Vcc
-
4
55
8
UNITS
pF
Vdc
Vdc
mA
mA
%
ns
Notes
(Voh)
(Vol)
(Ioh)
(Iol)
CLIPPED SINEWAVE OUTPUT CHARACTERISTICS
PARAMETER
Load
Output Voltage (< 40 MHz)
Output Voltage (> 40 MHz)
Table 13.0
Notes
MINIMUM
-
1.00
0.80
NOMINAL
10K //10pF
-
-
MAXIMUM
-
-
-
UNITS
6
V pk-pk
V pk-pk