- 您現在的位置：買賣IC網 > PDF目錄2018 > SY87813LHG (Micrel Inc)IC CLOCK/DATA REC 1.3GBPS 32TQFP PDF資料下載
參數資料
| 型號： | SY87813LHG |
| 廠商： | Micrel Inc |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK/DATA REC 1.3GBPS 32TQFP |
| 標準包裝： | 250 |
| 系列： | AnyRate® |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，ATM 應用 |
| 輸入： | PECL |
| 輸出： | PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:3 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.3Gbps |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP 裸露焊盤 |
| 供應商設備封裝： | 32-EPAD-TQFP |
| 包裝： | 托盤 |
| 其它名稱： | 576-1586 |
Micrel, Inc.
SY87813L
November 2006
13
M9999-112806-B
hbwhelp@micrel.com or (408) 955-1690
Appendix A
Layout and General Suggestions
1.
Establish controlled impedance stripline, microstrip, or
coplanar construction techniques.
2.
Signal paths should have approximately the same width
as the device pads.
3.
All differential paths are critical timing paths, where
skew should be matched to within ±10ps.
4.
Signal trace impedance should not vary more than
±5%. If in doubt, perform TDR analysis of all high-speed
signal traces.
5.
Maintain compact filter networks as close to filter pins
as possible. Provide ground plane relief under filter path
to reduce stray capacitance. Be careful of crosstalk
coupling into the filter network.
6.
Maintain low jitter on the REFCLK input. Isolate the
XTAL oscillator from power supply noise by adequately
decoupling. Keep XTAL oscillator close to device, and
minimize capacitive coupling from adjacent signals.
7.
Higher speed operation may require use of
fundamental-tone (third-overtone typically has more
jitter) crystal-based oscillator for optimum performance.
Evaluate and compare candidates by measuring
TXCLK jitter.
8.
All unused outputs must be terminated. To conserve
power, unused PECL outputs can be terminated with a
1k resistor to VEE.
相關PDF資料 |
PDF描述 |
|---|---|
| SY89295UTI TR | IC DELAY LINE 1024TAP 32-TQFP |
| SY89296UTI TR | IC DELAY LINE 1024TAP 32-TQFP |
| SY89297UMH TR | IC DELAY LINE 1024TAP 2NS 24-MLF |
| SY897132LKY TR | IC LINK REPLICATOR 28TSSOP |
| TC1320EUATR | IC DAC 8BIT 2WIRE I2C 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SY87813LHG TR | 功能描述:計時器和支持產品 3.3V Any-Rate 32-1250 Mbps CDR (PbSn/I Temp/32 Pin EP-TQFP/T+R) RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| SY87813LHGTR | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V, 28Mbps to 1.3Gbps AnyRate Clock and Data Recovery |
| SY88022ALMG | 功能描述:激光驅動器 10Gbps FP/DFB LDD w/ Bias RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| SY88022ALMG TR | 功能描述:激光驅動器 10Gbps FP/DFB LDD w/ Bias RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| SY88022L | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:11.3Gbps Laser Diode Driver |
發布緊急采購，3分鐘左右您將得到回復。