- 您現在的位置：買賣IC網 > PDF目錄380772 > STM708TM6F (意法半導體) 3V Supervisor PDF資料下載
參數資料
| 型號： | STM708TM6F |
| 廠商： | 意法半導體 |
| 英文描述： | 3V Supervisor |
| 中文描述： | 3V的監 |
| 文件頁數： | 6/26頁 |
| 文件大?。?/td> | 251K |
| 代理商： | STM708TM6F |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
STM706T/S/R; STM706P; STM708T/S/R
6/26
Pin Descriptions
MR.
A logic low on MR asserts the reset output.
Reset remains asserted as long as MR is low and
for t
rec
after MR returns high. This active-low input
has an internal pull-up. It can be driven from a TTL
or CMOS logic line, or shorted to ground with a
switch. Leave open if unused.
WDI.
If WDI remains high or low for 1.6sec, the in-
ternal watchdog timer runs out and reset (or WDO)
is triggered. The internal watchdog timer clears
while reset is asserted or when WDI sees a rising
or falling edge.
The watchdog function cannot be disabled by al-
lowing the WDI pin to float.
WDO.
WDO goes low when a transition does not
occur on WDI within 1.6sec, and remains low until
a transition occurs on WDI (indicating the watch-
dog interrupt has been serviced). WDO also goes
low when V
CC
falls below the reset threshold; how-
ever, unlike the reset output, WDO goes high as
soon as V
CC
exceeds the reset threshold.
Note:
For those devices with a WDO output, a
watchdog timeout will not trigger reset unless
WDO is connected to MR.
RST.
Pulses low for t
rec
when triggered, and stays
low whenever V
CC
is below the reset threshold or
when MR is a logic low. It remains low for t
rec
after
either V
CC
rises above the reset threshold, the
watchdog triggers a reset, or MR goes from low to
high.
RST.
Pulses high for t
rec
when triggered, and
stays high whenever V
CC
is above the reset
threshold or when MR is a logic high. It remains
high for t
rec
after either V
CC
falls below the reset
threshold, the watchdog triggers a reset, or MR
goes from high to low.
PFI.
When PFI is less than V
PFI
, PFO goes low;
otherwise, PFO remains high. Connect to ground
if unused.
PFO.
When PFI is less than V
PFI
, PFO goes low;
otherwise, PFO remains high. Leave open if un-
used.
Table 3. Pin Description
Pin
Name
Function
STM706P
STM706T/S/R
STM708T/S/R
SO8
TSSOP8
SO8
TSSOP8
SO8
TSSOP8
1
3
1
3
1
3
MR
Push-button Reset Input
6
8
6
8
–
–
WDI
Watchdog Input
8
2
8
2
–
–
WDO
Watchdog Output
–
–
7
1
7
1
RST
Active-Low Reset Output
7
1
–
–
8
2
RST
Active-High Reset Output
2
4
2
4
2
4
V
CC
Supply Voltage
4
6
4
6
4
6
PFI
PFI Power-fail Input
5
7
5
7
5
7
PFO
PFO Power-fail Output
3
5
3
5
3
5
V
SS
Ground
–
–
–
–
6
8
NC
No Connect
相關PDF資料 |
PDF描述 |
|---|---|
| STM802BD | SOLENOID CONTROLLER IC |
| STM802BDR | SOLENOID CONTROLLER IC |
| STM809LW16F | Reset Circuit |
| STM809TWX6F | Reset Circuit |
| STM810 | Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STM7096N | 制造商:SAMHOP 制造商全稱:SAMHOP 功能描述:N-Channel E nhancement Mode Field Effect Transistor |
| STM710 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 400V V(BR)DSS | 2A I(D) | TO-220AB |
| STM711 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 350V V(BR)DSS | 2A I(D) | TO-220AB |
| STM712 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 400V V(BR)DSS | 1.3A I(D) | TO-220 |
| STM713 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 350V V(BR)DSS | 1.7A I(D) | TO-220AB |
發布緊急采購，3分鐘左右您將得到回復。