參數資料
型號： STM1403
廠商： 意法半導體
英文描述： Security Supervisor with Battery Switchover(帶電池轉換功能的安全監控器)
中文描述： 安全監控與電池切換（帶電池轉換功能的安全監控器）
文件頁數： 17/35頁
文件大?。?/td> 356K
代理商： STM1403
STM1403
Tamper detection
17/35
Tamper detection
Physical
There are four (4) high-impedance physical tamper detect input pins, 2 normally set to High
(NH) and 2 normally set to Low (NL). Each input is designed with a glitch immunity (see
Table 7 on page 29
). These inputs can be connected externally to several types of actuator
devices (e.g., switches, wire mesh). A tamper on any one of the four inputs that causes its
state to change will trigger the security alarm (SAL) and drive it to active-low. Once the
tamper condition no longer exists, the SAL will return to its normal High state.
TP
1
and TP
3
are set Normally to High (NH). They are connected externally through a closed
switch or a high-impedance resistor to V
OUT
(in the case of STM1403A) or V
TPU
(in the case
of STM1403B/C), A tamper condition will be detected when the input pin is pulled low (see
Figure 5
and
Figure 6
). If not used, tie the pin to V
OUT
or V
TPU
.
TP
2
and TP
4
are set Normally to Low (NL). They are connected externally through a high-
impedance resistor or a closed switch to V
SS
. A tamper condition will be detected when the
input pin is pulled high (see
Figure 7
and
Figure 8
). If not used, tie the pin to V
SS
.
Supply voltage
The internally switched supply voltage, V
INT
(either V
CC
input or V
BAT
input) is continuously
monitored. If V
INT
should exceed the over voltage trip point, V
HV
(set at 4.2V, typical), or
should go below the under voltage trip point, V
LV
(set at 2.0v, typical). SAL will be driven
active-low. Once the tamper condition no longer exists, the SAL pin will return to its normal
High state.
When no tamper condition exists, SAL is normally High (see
Section : Pin descriptions on
page 11
).
When a tamper is detected, the SAL is activated (driven low), independent of the part type.
V
OUT
can be driven to one of three states, depending on which variant of STM1403 is being
used (see
Table 1: Device options on page 1
):
ON;
High-Z; or
Ground (V
SS
).
The STM1403 must be initially powered above V
RST
to enable the tamper detection alarms.
For example, if the battery is on while V
CC
= 0V, no alarm condition can be detected until
V
CC
rises above V
RST
(and t
rec
expires). From this point on, alarms can be detected either
on battery or V
CC
. This is done to avoid false alarms when the device goes from no power to
its operational state.
●
●
●
Note:
相關PDF資料
PDF描述
STM1404 Security Supervisor with Battery Switchover(帶電池轉換功能的安全監控器)
STM3210B-EVAL STM32F10XXX Evaluation Board(STM32F10XXX評估板)
STM3210B-PRIMER Raisonance STM32 Primer for fun, easy evaluation and development with STM32(STM32F10XXX系列開發工具，包括Raisonance開發軟件)
STM401-2 RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS
STM326-2 RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS
相關代理商/技術參數
參數描述
STM1403_08 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
STM1403ARMQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
STM1403ARM-Q6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3V FIPS-140 Security Supervisor with Battery Switchover
STM1403ARNQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
STM1403ARN-Q6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3V FIPS-140 Security Supervisor with Battery Switchover
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*