- 您現在的位置：買賣IC網 > PDF目錄380766 > STM1403 (意法半導體) Security Supervisor with Battery Switchover(帶電池轉換功能的安全監控器) PDF資料下載
參數資料
| 型號： | STM1403 |
| 廠商： | 意法半導體 |
| 英文描述： | Security Supervisor with Battery Switchover(帶電池轉換功能的安全監控器) |
| 中文描述： | 安全監控與電池切換（帶電池轉換功能的安全監控器） |
| 文件頁數： | 13/35頁 |
| 文件大?。?/td> | 356K |
| 代理商： | STM1403 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
STM1403
Pin descriptions
13/35
V
OUT
This is the Supply Voltage Output. When V
CC
rises above V
SO
(Battery Backup Switchover
Voltage), V
OUT
is supplied from V
CC
. In this condition, V
OUT
may be connected externally to
V
CC
through a p-channel MOSFET switch. When V
CC
falls below the lower value of V
SW
(~2.4V), or V
BAT
, V
OUT
is supplied from V
BAT
. It is recommended that the V
OUT
pin be
connected externally to a capacitor that will retain a charge for a period of time, in case an
intruder forces V
CC
or V
BAT
to Ground. The rectifying diode connected from the positive
terminal of the battery to the V
BAT
pin of the STM1403 will prevent discharge of the
capacitor.
Three variations of parts will be offered with the following options:
1.
STM1403A: V
OUT
remains ON when SAL is active-low; Vccsw pin will continue to
operate in normal mode (see
Section : Vccsw, V
CC
switch output on page 11
);
2.
STM1403B: V
OUT
is taken to High-Z when SAL is active-low; Vccsw pin will be set to
High when this occurs; and
3.
STM1403C: V
OUT
is driven to Ground when SAL is active-low; Vccsw pin will be set to
High when this occurs.
V
TPU
For STM1403B and STM1403C, this pin provides pull-up voltage for the physical tamper
pins (TP1-4). This pin is not to be used as voltage supply source for any other purpose.
Note:
V
TPU
is the internally switched supply voltage from either the V
CC
pin or the V
BAT
pin.
V
CC
This is the Supply voltage (2.2V to 3.6V).
V
BAT
This is the secondary (backup battery) supply voltage. The pin is connected to the positive
terminal of the battery with a rectifying diode like the BAT54J from STMicroelectronics for
reverse charge protection. Voltage at this pin, after diode rectification, will be approximately
0.2V less than the battery voltage, and will depend on the type of battery used as well as the
I
BAT
being drawn. (A capacitor of at least 1.0μF connected between the V
BAT
pin and V
SS
is
required.) If no battery is used, connect the V
BAT
pin to the V
CC
pin.
V
SS
Ground, V
SS
, is the reference for the power supply. It must be connected to system ground.
相關PDF資料 |
PDF描述 |
|---|---|
| STM1404 | Security Supervisor with Battery Switchover(帶電池轉換功能的安全監控器) |
| STM3210B-EVAL | STM32F10XXX Evaluation Board(STM32F10XXX評估板) |
| STM3210B-PRIMER | Raisonance STM32 Primer for fun, easy evaluation and development with STM32(STM32F10XXX系列開發工具，包括Raisonance開發軟件) |
| STM401-2 | RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS |
| STM326-2 | RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STM1403_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover |
| STM1403ARMQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover |
| STM1403ARM-Q6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3V FIPS-140 Security Supervisor with Battery Switchover |
| STM1403ARNQ6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover |
| STM1403ARN-Q6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3V FIPS-140 Security Supervisor with Battery Switchover |
發布緊急采購，3分鐘左右您將得到回復。