- 您現在的位置：買賣IC網 > PDF目錄380765 > STLC1 (意法半導體) LED LAMPS CLUSTER DRIVER PDF資料下載
參數資料
| 型號： | STLC1 |
| 廠商： | 意法半導體 |
| 英文描述： | LED LAMPS CLUSTER DRIVER |
| 中文描述： | LED節能燈驅動集群 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 298K |
| 代理商： | STLC1 |
STLC1
7/16
only when the OUT voltage is about 95% of its
final value. Such a start-up phase takes place
when only one input is enabled.
LOW SIDE DRIVER:
The purpose of the low side drivers is to connect
the LED cluster to ground, creating a path for the
current. Using external resistors, current flowing
into the LED cluster is set according to the
following formula:
V
R
T
(
where (see typical application schematic):
R
L
= R
LT
, R
LS
, or R
LR
R
T
= R
TT
, R
TS
, or R
TR
R
(on)
= Static drain to source LSD on resistance
V
OUT
= Output Voltage
V
ARRAY
= Expected LED array voltage drop.
LSD over-current protection and under-current
diagnostic (see LAMP OUTAGE DETECTION
section) is performed by sensing the voltage on
resistors, when the
corresponding
enabled.
If the voltage on
exceeds V
H-SHORT
, the
over-current protection acts by reducing the LSD
average current by switching ON and OFF the
LSD itself.
LSD
are
LAMP OUTAGE DETECTION
Resistors are used to sense the LED array
current. In case one or more LEDs fail (open
circuit) the current on the corresponding resistor
will
drop
due
to
the increased LED
resistance. As soon as the voltage drop on
lower than V
LOUT
, a LED lamp fault condition is
array
is
detected and the LMP-OUT pin becomes active
(low).
The
LAMP-OUTAGE
AND-ed with each input, that is a fault condition
can be detected only when the LED arrays are
enabled.
functionality
is
DIMMING
The dimming of the LED lamps can be obtained by
using the internal PULSE WIDTH controller (it
drives the LSD TAIL and STOP gates). The duty
cycle of this internal oscillator (whose frequency is
380Hz typical) can be set, forcing the voltage of
the CNTL pin to be a fraction of V
REF
, by using a
simple resistor divider (as shown in the typical
application scheme).
In this case the duty cycle percentage can be
calculated
with
the
following
formula:
approximated
The TS-PWM pin voltage, according to the
TABLE1 determines which LSD is PULSE WIDTH
CONTROLLER driven. Internal dimming can only
be performed on the TAIL and STOP arrays. The
TURN array can be externally dimmed (as well as
TAIL and STOP) by driving the corresponding
input witha a square pulse signal whose maximum
frequency must be 200Hz.
I
ARRAY
ARRAY
R
L
R
on
)
+
+
----------------------V
=
DC%
3.8 if
R
+
R
C1
R
C2
----------------------------
V
REF
--0.2
≤
R
+
R
C1
R
C2
----------------------------
100 Elsewhere
相關PDF資料 |
PDF描述 |
|---|---|
| STLC2150 | BLUETOOTH RADIO TRANSCEIVER |
| STLC2415 | BLUETOOTH BASEBAND WITH INTEGRATED FLASH |
| STLC2500 | BLUETOOTH⑩ SINGLE CHIP |
| STLC3055 | WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT |
| STLC3055Q | WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STLC1502 | 制造商:STMicroelectronics 功能描述:VOICE OVER IP PROCESSOR - Bulk |
| STLC1502D | 制造商:STMicroelectronics 功能描述:VOIP STRADIVARIUS 1 - Trays |
| STLC1502P | 制造商:STMicroelectronics 功能描述:VOICE OVER IP PROCESSOR - Trays |
| STLC1510 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:NorthenLite G.lite DMT Transceiver |
| STLC1511 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:NorthenLite⑩ G.lite BiCMOS Analog Front-End Circuit |
發布緊急采購，3分鐘左右您將得到回復。