- 您現在的位置：買賣IC網 > PDF目錄380762 > STCN75DS2E (意法半導體) Digital temperature sensor and thermal watchdog PDF資料下載
參數資料
| 型號： | STCN75DS2E |
| 廠商： | 意法半導體 |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Digital temperature sensor and thermal watchdog |
| 中文描述： | 數字溫度傳感器和熱看門狗 |
| 文件頁數： | 12/35頁 |
| 文件大?。?/td> | 194K |
| 代理商： | STCN75DS2E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Operation
STCN75
12/35
2.3
Comparator mode
In Comparator mode, each time a temperature-to-digital (T-to-D) conversion occurs, the new
digital temperature is compared to the value stored in the T
OS
and T
HYS
registers. If a fault
tolerance number of consecutive temperature measurements are greater than the value
stored in the T
OS
register, the OS/INT output will be asserted.
For example, if the FT1 and FT0 Bits are equal to “10” (fault tolerance = 4), four consecutive
temperature measurements must exceed T
OS
to activate the OS/INT output. Once the
OS/INT output is active, it will remain active until the first time the measured temperature
drops below the temperature stored in the T
HYS
register, whereupon it will reset to its
inactive state.
Putting the device into Shutdown mode does not clear OS/INT in Comparator mode.
2.4
Interrupt mode
In Interrupt mode, the OS/INT output becomes active when the measured temperature
exceeds the T
OS
value a consecutive number of times as determined by the Fault Tolerance
bits (FT1, FT0) value in the Configuration register. Once activated, the OS/INT can only be
cleared by reading from any register (temperature, configuration, T
OS
, or T
HYS
) on the
device. Once the OS/INT has been deactivated, it will only be reactivated when the
measured temperature falls below the T
HYS
value a consecutive number of times equal to
the FT value. This mode is better suited for interrupt driven microprocessor based systems.
相關PDF資料 |
PDF描述 |
|---|---|
| STCN75DS2F | Digital temperature sensor and thermal watchdog |
| STCN75M2E | Digital temperature sensor and thermal watchdog |
| STCN75M2F | Digital temperature sensor and thermal watchdog |
| STCS1 | 1.5 A max constant current LED driver |
| STCS1PHR | 1.5 A max constant current LED driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STCN75DS2F | 功能描述:板上安裝溫度傳感器 Digital TEMP sensor thermal watchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| STCN75M2E | 功能描述:板上安裝溫度傳感器 Digital Temp Snsr Thermal Watchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| STCN75M2F | 功能描述:板上安裝溫度傳感器 Digital Temp Snsr Thermal Watchdog RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ST-COAX-REMOTES | 制造商:Black Box Corporation 功能描述:SOHOTEST Replacement Coax Remotes, #1 5 |
| STCOMPATABLEFIBREOPTICCONN | 制造商:3M Electronic Products Division 功能描述:ST(R) II compatible fibre connector plug |
發布緊急采購，3分鐘左右您將得到回復。