- 您現在的位置：買賣IC網 > PDF目錄380762 > STCF03 (意法半導體) High power white LED driver with I2C⑩ interface PDF資料下載
參數資料
| 型號： | STCF03 |
| 廠商： | 意法半導體 |
| 元件分類： | LED驅動器 |
| 英文描述： | High power white LED driver with I2C⑩ interface |
| 中文描述： | 大功率白光LED驅動器具有I2C⑩接口 |
| 文件頁數： | 14/35頁 |
| 文件大?。?/td> | 455K |
| 代理商： | STCF03 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Introduction
STCF03
14/35
7.2.4
ADD pin
With this pin it is possible to select one of the 4 possible I
2
C slave addresses. No internal
pull-up nor pull-down is provided. The pin has to be connected either GND, V
I
, SCL or SDA
to select the desired I
2
C slave address (see
Table 6.
)
7.2.5
TMSK pin
This pin can be used to implement the TX masking function. This function has effect only for
Flash current settings higher than 200 mA (bit FDIM_3=1). Under this condition, when this
pin is pulled high by the P, the current flowing in the LED is forced at 200 mA typ. No internal
pull-up nor pull-down is provided: to be externally wired to GND if TX masking function is not
used.
7.3
I
2
C BUS interface
Data transmission from the main μP STCF03 and vice versa takes place through the 2 wires
I
2
C bus interface wires, consisting of the two lines SDA and SCL (pull-up resistors to a
positive supply voltage must be externally connected). The recommended maximum voltage
of these signals should be 3.0 V.
7.4
Data validity
As shown in
Figure 4
, the data on the SDA line must be stable during the high period of the
clock. The HIGH and LOW state of the data line can only change when the clock signal on
the SCL line is LOW.
Table 7. Address table
ADD pin
A7
A6
A5
A4
A3
A2
A1
A0
GND
0
1
1
0
0
0
0
R/W
VBAT
0
1
1
0
0
0
1
R/W
SDAL
0
1
1
0
0
1
0
R/W
SCL
0
1
1
0
0
1
1
R/W
Figure 4.
Data validity on the I
2
C Bus
相關PDF資料 |
PDF描述 |
|---|---|
| STCF03PNR | High power white LED driver with I2C⑩ interface |
| STCF03TBR | High power white LED driver with I2C⑩ interface |
| STCN75 | Digital temperature sensor and thermal watchdog |
| STCN75DS2E | Digital temperature sensor and thermal watchdog |
| STCN75DS2F | Digital temperature sensor and thermal watchdog |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STCF03I | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High power white LED driver with IC interface |
| STCF03I_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High power white LED driver with IC interface |
| STCF03ITBR | 功能描述:LED照明驅動器 HP white LED driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| STCF03PNR | 功能描述:LED照明驅動器 Hi Pwr white LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| STCF03TBR | 功能描述:LED照明驅動器 HP white LED driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。