- 您現在的位置：買賣IC網 > PDF目錄380759 > STA506 (意法半導體) 40V 4A QUAD POWER HALF BRIDGE PDF資料下載
參數資料
| 型號： | STA506 |
| 廠商： | 意法半導體 |
| 英文描述： | 40V 4A QUAD POWER HALF BRIDGE |
| 中文描述： | 40V的4A條四重功率半橋 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 142K |
| 代理商： | STA506 |
STA506
8/14
There are two possible modes subsequent to activating a fault:
–
1) SHUTDOWN mode
: with FAULT (pull-up resistor) and TRI-STATE pins independent, an activated
fault will disable the device, signaling low at the FAULT output.
The device may subsequently be reset to normal operation by toggling the TRI-STATE pin from
High to Low to High using an external logic signal.
–
2) AUTOMATIC recovery mode:
This is shown in the Application Circuit of fig.1.
The FAULT and TRI-STATE pins are shorted together and connected to a time constant circuit com-
prising R59 and C58.
An activated FAULT will force a reset on the TRI-STATE pin causing normal operation to resume fol-
lowing a delay determined by the time constant of the circuit.
If the fault condition is still present , the circuit operation will continue repeating until the fault condition
is removed .
An increase in the time constant of the circuit will produce a longer recovery interval. Care must be
taken in the overall system design as not to exceed the protection thesholds under normal operation.
3.3 Power Outputs:
The STA506 power and output pins are duplicated to provide a low impedance path for the device's bridged
outputs .
All duplicate power, ground and output pins must be connected for proper operation.
The PWRDN or TRI-STATE pins should be used to set all MOSFETS to the Hi-Z state during power-up until the
logic power supply, V
L
, is settled.
3.4 Parallel Output / High Current Operation:
When using DDX Mode output , the STA506 outputs can be connected in parallel in order to increase the output
current capability to a load.
In this configuration the STA506 can provide 80W into 8 ohm or up to 120W into 4ohm.
This mode of operation is enabled with the CONFIG pin (pin.24) connected to VREG1 and the inputs combined
INLA=INLB, INRA=INRB and the outputs combined OUTLA=OTLB, OUTRA=OUTRB.
3.5 Additional Informations:
Output Filter: A passive 2nd-order passive filter is used on the STA506 power outputs to reconstruct an analog
Audio Signal .
System performance can be significantly affected by the output filter design and choice of passive components.
A filter design for 6ohm/8ohm loads is shown in the Typical Application circuit of fig.1. Figure 9 shows a filter
design suitable for 4ohm loads.
Figure 10 shows a filter for bridge mode , 4 ohm loads.
Power Dissipation & Heat Sink requirements:
The power dissipated within the device will depend primarily
on the supply voltage, load impedance and output modulation level.
The PowerSO36 package of the STA506 includes an exposed thermal slug on the top of the device to provide
a direct thermal path from the IC to the heatsink.
Careful consideration must be given to the overall thermal design . See figure 8 for power derating
versus Slug temperature using different heatsinks and considering the Rth-jc =1.5°C/W.
相關PDF資料 |
PDF描述 |
|---|---|
| STA5100 | 140W MONO BASH POWER AMPLIFIER |
| STA515 | 200W MONO BASH POWER AMPLIFIER |
| STA5150 | 200W MONO BASH POWER AMPLIFIER |
| STA517B | 60 V 6 A quad power half bridge |
| STA517B13TR | 60 V 6 A quad power half bridge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STA50613TR | 功能描述:音頻放大器 40V 4.0A Half Bridge RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| STA-5063 | 制造商:RF Micro Devices Inc 功能描述:IC AMP GEN-PURP 3.3V SOT-363 |
| STA-5063Z | 制造商:SIRENZA 制造商全稱:SIRENZA 功能描述:3.3 - 6.2 GHz General Purpose 3.3V 15dBm Amplifier |
| STA5063ZSR | 制造商:RF Micro Devices Inc 功能描述:IC RF AMP GP 15DBM SOT-363 |
| STA506A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:45V 4A QUAD POWER HALF BRIDGE |
發布緊急采購，3分鐘左右您將得到回復。