- 您現在的位置：買賣IC網 > PDF目錄381107 > ST95P02M1 (意法半導體) SPI Serial EEPROM PDF資料下載
參數資料
| 型號： | ST95P02M1 |
| 廠商： | 意法半導體 |
| 英文描述： | SPI Serial EEPROM |
| 中文描述： | SPI串行EEPROM |
| 文件頁數： | 7/16頁 |
| 文件大小： | 151K |
| 代理商： | ST95P02M1 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
C
Q
AI01072B
S
D
HOLD
tCLHX
tHXCH
tHXCH
tCLHX
tHHQX
tHLQZ
Figure 7. Hold Timing
Write Protect (W).
This pin is for hardware write
protect. When W is low, non-volatile writes to the
ST95P02 are disabled but any other operation
stays enabled. When W is high, all operations
including non-volatile writes are available. W going
low at any time before the last bit D0 of the data
stream will reset the write enable latch and prevent
programming. No action on W or on the write
enable latch can interrupt a write cycle which has
commenced.
Hold (HOLD).
The HOLD pin is used to pause
serial communications with a ST95P02 without
resetting the serial sequence. To take the Hold
condition into account, the product must be se-
lected (S = 0). Then the Hold state is validated by
a high to low transition on HOLD when C is low. To
resume the communications, HOLD is brought high
when C is low. During Hold condition D, Q, and C
are at a high impedance state.
When the ST95P02 is under Hold condition, it is
possible to deselect it. However, the serial commu-
nications will remain paused after a reselect, and
the chip will be reset.
OPERATIONS
All instructions, addresses and data are shifted in
and out of the chip MSB first. Data input (D) is
sampled on the first rising edge of clock (C) after
the chip select (S) goes low. Prior to any operation,
a one-byte instruction code must be entered in the
chip. This code is entered via the data input (D),
and latched on the rising edge of the clock input
(C). To enter an instruction code, the product must
have been previously selected (S = low). Table 7
shows the instruction set and format for device
operation. When an invalid instruction is sent (one
not contained in Table 7), the chip is automatically
deselected.
Write Enable (WREN) and Write Disable (WRDI)
The ST95P02 contains a write enable latch. This
latch must be set prior to every WRITE or WRSR
operation. The WREN instruction will set the latch
and the WRDI instruction will reset the latch. The
latch is reset under all the following conditions:
– W pin is low
– Power on
– WRDI instruction executed
– WRSR instruction executed
– WRITE instruction executed
As soon as the WREN or WRDI instruction is
received by the ST95P02, the circuit executes the
instruction and enters a wait mode until it is dese-
lected.
7/16
ST95P02
相關PDF資料 |
PDF描述 |
|---|---|
| ST95P02M1TR | SPI Serial EEPROM |
| ST95P02M3 | SPI Serial EEPROM |
| ST95P02M3TR | SPI Serial EEPROM |
| ST95P02M6 | SPI Serial EEPROM |
| ST95P02M6TR | SPI Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST95P02M1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPI Serial EEPROM |
| ST95P02M3 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPI Serial EEPROM |
| ST95P02M3TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPI Serial EEPROM |
| ST95P02M6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPI Serial EEPROM |
| ST95P02M6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPI Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。