參數資料
型號: ST7260E2M1/XXX
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
封裝: 0.300 INCH, LEAD FREE, PLASTIC, SOP-24
文件頁數: 73/118頁
文件大小: 2304K
代理商: ST7260E2M1/XXX
ST7260
58/117
11.3 SERIAL COMMUNICATIONS INTERFACE (SCI)
11.3.1 Introduction
The Serial Communications Interface (SCI) offers
a flexible means of full-duplex data exchange with
external equipment requiring an industry standard
NRZ asynchronous serial data format. The SCI of-
fers a very wide range of baud rates using two
baud rate generator systems.
11.3.2 Main Features
Full duplex, asynchronous communications
NRZ standard format (Mark/Space)
Independently
programmable
transmit
and
receive baud rates up to 250K baud.
Programmable data word length (8 or 9 bits)
Receive buffer full, Transmit buffer empty and
End of Transmission flags
Two receiver wake-up modes:
– Address bit (MSB)
– Idle line
Muting function for multiprocessor configurations
Separate
enable bits for Transmitter and
Receiver
Four error detection flags:
– Overrun error
– Noise error
– Frame error
– Parity error
Six interrupt sources with flags:
– Transmit data register empty
– Transmission complete
– Receive data register full
– Idle line received
– Overrun error detected
– Parity error
Parity control:
– Transmits parity bit
– Checks parity of received data byte
Reduced power consumption mode
11.3.3 General Description
The interface is externally connected to another
device by two pins (see Figure 36):
– TDO: Transmit Data Output. When the transmit-
ter and the receiver are disabled, the output pin
returns to its I/O port configuration. When the
transmitter and/or the receiver are enabled and
nothing is to be transmitted, the TDO pin is at
high level.
– RDI: Receive Data Input is the serial data input.
Oversampling techniques are used for data re-
covery by discriminating between valid incoming
data and noise.
Through these pins, serial data is transmitted and
received as frames comprising:
– An Idle Line prior to transmission or reception
– A start bit
– A data word (8 or 9 bits) least significant bit first
– A Stop bit indicating that the frame is complete.
This interface uses two types of baud rate generator:
– A conventional type for commonly-used baud
rates.
相關PDF資料
PDF描述
ST72T141K2M6XXX 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34
ST72T141K2M3XXX 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34
ST72T141K2MARE 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34
ST7FL09Y0MATRE 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
ST7FL09Y0MBE 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
相關代理商/技術參數
參數描述
ST72611F1 制造商:STMicroelectronics 功能描述:LOW SPEED USB 8-BIT MCU WITH 3 ENDPOINTS,FLASH MEMORY, - Bulk
ST7263-EMU2 功能描述:仿真器/模擬器 ST7 Emulator Board RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
ST7265X-EVAL/MS 制造商:STMicroelectronics 功能描述:ST6 EVAL BD - Bulk
ST7265X-EVAL/PFD 制造商:STMicroelectronics 功能描述:USB FLASH EVAL - Bulk
ST7266 制造商:6940 功能描述:ST7266