參數資料
型號： ST62T03C
廠商： 意法半導體
英文描述： 8-Bit OTP MCUs with A/D Converter, Oscillator Safeguard, Safe Reset and 16 Pins(８位ＯＴＰ微處理器（８Ｍ）)
中文描述： 8位微控制器與檢察官辦公室的A / D轉換器，振蕩器保障，安全復位和16引腳（8位檢察官辦公室微處理器（8米））
文件頁數： 41/70頁
文件大?。?/td> 747K
代理商： ST62T03C
41/70
ST62T00C/T01C ST62T03C/E01C
A/D CONVERTER
(Cont’d)
Since the ADC is on the same chip as the micro-
processor, the user should not switch heavily load-
ed output signals during conversion, if high preci-
sion is required. Such switching will affect the sup-
ply voltages used as analog references.
The accuracy of the conversion depends on the
quality of the power supplies (V
DD
and V
SS
). The
user must take special care to ensure a well regu-
lated reference voltage is present on the V
DD
and
V
SS
pins (power supply voltage variations must be
less than 5V/ms). This implies, in particular, that a
suitable decoupling capacitor is used at the V
DD
pin.
The converter resolution is given by::
The Input voltage (Ain) which is to be converted
must be constant for 1μs before conversion and
remain constant during conversion.
Conversion resolution can be improved if the pow-
er supply voltage (V
DD
) to the microcontroller is
lowered.
In order to optimise conversion resolution, the user
can configure the microcontroller in WAIT mode,
because this mode minimises noise disturbances
and power supply variations due to output switch-
ing. Nevertheless, the WAIT instruction should be
executed as soon as possible after the beginning
of the conversion, because execution of the WAIT
instruction may cause a small variation of the V
DD
voltage. The negative effect of this variation is min-
imized at the beginning of the conversion when the
converter is less sensitive, rather than at the end
of conversion, when the less significant bits are
determined.
The best configuration, from an accuracy stand-
point, is WAIT mode with the Timer stopped. In-
deed, only the ADC peripheral and the oscillator
are then still working. The MCU must be woken up
from WAIT mode by the ADC interrupt at the end
of the conversion. It should be noted that waking
up the microcontroller could also be done using
the Timer interrupt, but in this case the Timer will
be working and the resulting noise could affect
conversion accuracy.
A/D Converter Control Register (ADCR)
Address: 0D1h
—
Read/Write
Bit 7 =
EAI
: Enable A/D Interrupt.
If this bit is set to
“1” the A/D interrupt is enabled, when EAI=0 the
interrupt is disabled.
Bit 6 =
EOC
: End of conversion.Read Only. This
read only bit indicates when a conversion has
been completed. This bit is automatically reset to
“0” when the STA bit is written. If the user is using
the interrupt option then this bit can be used as an
interrupt pending bit. Data in the data conversion
register are valid only when this bit is set to “1”.
Bit 5 =
STA
: Start of Conversion. Write Only Writ-
ing a “1” to this bit will start a conversion on the se-
lected channel and automatically reset to “0” the
EOC bit. If the bit is set again when a conversion is
in progress, the present conversion is stopped and
a new one will take place. This bit is write only, any
attempt to read it will show a logical zero.
Bit 4 =
PDS
: Power Down Selection. This bit acti-
vates the A/D converter if set to “1”. Writing a “0” to
this bit will put the ADC in power down mode (idle
mode).
Bit 3-0 =
D3-D0.
Not used
A/D Converter Data Register (ADR)
Address: 0D0h
—
Read only
Bit 7-0 =
D7-D0
: 8 Bit A/D Conversion Result.
V
---------------------------
V
–
256
7
0
EAI
EOC
STA
PDS
D3
D2
D1
D0
7
0
D7
D6
D5
D4
D3
D2
D1
D0
57
相關PDF資料
PDF描述
ST62T00C 8-Bit OTP MCUs with A/D Converter, Oscillator Safeguard, Safe Reset and 16 Pins(8位OTP微處理器（8M）)
ST62T09C(中文) 8-Bit OTP/EPROM MCUs with A/D Converter,Oscillator Safeguard, Safe Reset and 20 Pins(8位OTP/EPROM微控制器(8M))
ST62T08C(中文) 8-Bit OTP/EPROM MCUs with A/D Converter,Oscillator Safeguard, Safe Reset and 20 Pins(8位OTP/EPROM微控制器(8M))
ST62T10C(中文) 8-Bit OTP/EPROM MCUs with A/D Converter,Oscillator Safeguard, Safe Reset and 20 Pins(8位OTP/EPROM微控制器(8M))
ST62E20C(中文) 8-Bit OTP/EPROM MCUs with A/D Converter,Oscillator Safeguard, Safe Reset and 20 Pins(8位OTP/EPROM微控制器(8M))
相關代理商/技術參數
參數描述
ST62T03CB6 功能描述:8位微控制器 -MCU OTP EPROM 1K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T03CB6 制造商:STMicroelectronics 功能描述:IC 8BIT MCU OTP 1K 62T03 DIP16
ST62T03CM3 功能描述:8位微控制器 -MCU ST6200C ST6201C ST6203C 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T03CM3/TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T03CM6 功能描述:8位微控制器 -MCU OTP EPROM 1K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*