參數資料
型號: ST6225CM1
廠商: 意法半導體
英文描述: 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
中文描述: 8位檢察官辦公室/存儲器與阿微控制器/ D轉換器,振蕩器保障,安全復位和28個引腳
文件頁數: 10/70頁
文件大?。?/td> 472K
代理商: ST6225CM1
10/70
10
ST62T15C/T25C/E25C
1.4 PROGRAMMINGMODES
1.4.1 Option Bytes
The two Option Bytes allow configuration capabili-
ty to the MCUs. Option byte’s content is automati-
cally read, and the selected options enabled,when
the chip reset is activated.
It can only be accessed during the programming
mode. This access is made either automatically
(copy from a master device) or by selecting the
OPTION BYTEPROGRAMMING modeof the pro-
grammer.
The option bytes are located in a non-user map.
No address has to be specified.
EPROM Code Option Byte (LSB)
EPROM Code Option Byte (MSB)
D15-D10.
Reserved. Must be cleared
EXTCNTL.
External STOP MODE control
.
. When
EXTCNTL is high, STOP mode is available with
watchdog active by setting NMI pin to one.. When
EXTCNTL is low, STOP mode is not availablewith
the watchdog active.
LVD.
LVDRESET enable.When this bit is set, safe
RESET is performed by MCU when the supply
voltage is too low. When this bit is cleared, only
power-on reset or external RESET are active.
PROTECT
. Readout Protection.This bit allowsthe
protection of the software contents against piracy.
When the bit PROTECT is set high, readout of the
OTP contents is prevented by hardware.. When
this bit is low, the user program can be read.
OSCIL
. Oscillator selection When this bit is low,
the oscillator must be controlled by a quartz crys-
tal, a ceramic resonator or an external frequency.
When itis high, the oscillator must be controlled by
an RC network, with only the resistor having to be
externally provided.
D5-D4.
Reserved. Must be cleared to zero.
NMI PULL.
NMI Pull-Up This bit must be set high
to configure the NMI pin with a pull-up resistor.
When it is low, no pull-up is provided
.
TIM PULL.
TIM Pull-Up This bit must be set high
to configure the TIMER pin with a pull-up resistor.
When it is low, no pull-up is provided
.
WDACT
. Thisbit controls the watchdog activation.
When it is high, hardware activation is selected.
The software activation is selected when WDACT
is low.
OSGEN
. Oscillator Safe Guard This bit must be
set high to enable the Oscillator Safe Guard.
When this bit is low, the OSG is disabled.
The Option byte is written during programming ei-
ther by using the PC menu (PC driven Mode) or
automatically (stand-alone mode)
7
0
PRO-
TECT
OSCIL
-
-
NMI
PULL
TIM
PULL
WDACT
OS-
GEN
15
8
-
-
-
-
-
-
EXTC-
NTL
LVD
相關PDF資料
PDF描述
ST6215CM1 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
ST6215CM3 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
ST6215CM6 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
ST6225CN3 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
ST6225CN6 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
相關代理商/技術參數
參數描述
ST6225CM1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST6225CM3/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
ST6225CM6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
ST6225CM6/HKN 制造商:STMicroelectronics 功能描述:ST6225CM6/HKN - Rail/Tube
ST6225CM6/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller