- 您現在的位置：買賣IC網 > PDF目錄299943 > ST52514K1 IC MAX 7000 CPLD 128 100-FBGA PDF資料下載
參數資料
| 型號： | ST52514K1 |
| 英文描述： | IC MAX 7000 CPLD 128 100-FBGA |
| 中文描述： | 8位重癥監護病房，10位ADC。兩個定時器/脈寬調制。 I2C總線。的SPI。脊髓損傷。提供了8K閃存 |
| 文件頁數： | 31/106頁 |
| 文件大?。?/td> | 1355K |
| 代理商： | ST52514K1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
4.2 Memory Programming
The Programming procedure writes the user
program
and
data into the Flash Memory,
EEPROM and Option Bytes. The programming
procedures are entered by setting the Vpp pin
equal to Vdd and releasing the Reset signal. The
following pins are used in Programming mode:
s
VPP
used to switch to programming mode
s
VDD
device supply
s
VSS
device ground
s
RESET
device reset
s
SCL
I2C serial clock
s
SDA
I2C serial data
During the device programming, the internal clock
is used, so the OSCin and OSCout pins don’t have
to be considered.
4.2.1 Programming Mode start. The
following
sequence starts the Programming Mode:
1.
VPP is set to VDD
2.
The device is Reset (RESET=VSS)
3.
The Reset is released (RESET=VDD)
4.
The internal oscillator starts at 10 MHz
5.
The memory is turned on
6.
The I2C Interface and Ports are initialized
7.
The I2C Interface is configured to work as
Slave, Receiver, 7-bit address and waits for
data
8.
The Start signal is sent to the chip followed by
the Slave Address 1010000 and the direction
bit set to 0 (the addressed slave waits for da-
ta). The device sends the acknowledge
9.
The Programming Mode code 00000000 is
sent and acknowledged
10. A command code is sent to the device
11. The procedure related to the command is ex-
ecuted
Table 4.2 Programming Mode Commands
Command
Code
Data in
Data out Erase
Description
BlockWrite
00000001
32
-
Yes
Write the currently addressed block with the 32 bytes
following the command. The Block locations are erased
before being written.
ByteWrite
00000010
2
-
Yes
Write the byte addressed by the next data sent in the
currently addressed page.
BlockErase
00000011
1
Yes
Erase the block addressed by 3 MSB of the next data sent
and inside the currently addressed page.
ByteErase
00000100
1
Yes
Erase the byte addressed by the next data sent and inside
the currently addressed page.
ByteRead
00000101
1
-
Read the byte addressed by the next data sent and inside
the current page. The read data is sent by the device after
the re-send of the Slave Address with the R/W bit changed.
GlobalErase
00001001
-
Yes
All the memory is erased.
FastBlockWrite 00001011
32
-
No
Write the currently addressed block with the 32 bytes
following the command. The Block locations aren’t erased.
SetPage
00001100
1
-
The currently addressed page is set with the next data sent.
ReadData
00001101
-
N
-
Read N consecutive bytes starting from the memory
location currently addressed. The read data is sent by the
device after the command is acknowledged. The current
memory absolute address is post-incremented.
IncBlock
00001111
-
The current block address is incremented modulo 8
(address 0 follows after address 7 and the Page is post-
incremented)
ReadStatus
00010011
-
1
-
This command is followed by a status data byte. Mostly
used in error condition and to check if the device is locked
相關PDF資料 |
PDF描述 |
|---|---|
| ST52514K3 | IC MAX 7000 CPLD 256 100-TQFP |
| ST525 | MAX 7000 CPLD 128 MC 100-FBGA |
| ST527 | IC MAX 7000 CPLD 512 208-PQFP |
| ST531 | IC MAX 7000 CPLD 160 100-TQFP |
| ST532 | MAX II CPLD 2210 LE 324-FBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST52514K3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH |
| ST526PND223MLZ | 制造商:COILCRAFT 制造商全稱:Coilcraft lnc. 功能描述:Coupled Inductors for Critical Applications |
| ST527 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | BJT | PNP | 200V V(BR)CEO | 8A I(C) | TO-3 |
| ST-5-28 | 功能描述:XFRMR PWR 115V 14VAC .84A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路，中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA，5 VAC @ 2A，6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高（最大）:66.80mm 端接類型:導線引線 |
| ST5-28 | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:POWER TRANSFORMER |
發布緊急采購，3分鐘左右您將得到回復。