- 您現在的位置：買賣IC網 > PDF目錄381095 > ST24C16M6TR (意法半導體) 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection PDF資料下載
參數資料
| 型號： | ST24C16M6TR |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| 中文描述： | 16千位串行I2C總線的EEPROM與用戶定義的塊寫保護 |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 126K |
| 代理商： | ST24C16M6TR |
Symbol
Alt
Parameter
Min
Max
Unit
t
CH1CH2
t
R
Clock Rise Time
1
μ
s
t
CL1CL2
t
F
Clock Fall Time
300
ns
t
DH1DH2
t
R
Input Rise Time
1
μ
s
t
DL1DL1
t
F
Input Fall Time
300
ns
t
CHDX
(1)
t
SU:STA
Clock High to Input Transition
4.7
μ
s
t
CHCL
t
HIGH
Clock Pulse Width High
4
μ
s
t
DLCL
t
HD:STA
Input Low to Clock Low (START)
4
μ
s
t
CLDX
t
HD:DAT
Clock Low to Input Transition
0
μ
s
t
CLCH
t
LOW
Clock Pulse Width Low
4.7
μ
s
t
DXCX
t
SU:DAT
Input Transition to Clock Transition
250
ns
t
CHDH
t
SU:STO
Clock High to Input High (STOP)
4.7
μ
s
t
DHDL
t
BUF
Input High to Input Low (Bus Free)
4.7
μ
s
t
CLQV (2)
t
AA
Clock Low to Next Data Out Valid
0.3
3.5
μ
s
t
CLQX
t
DH
Data Out Hold Time
300
ns
f
C
f
SCL
Clock Frequency
100
kHz
t
W
(3)
t
WR
Write Time
10
ms
Notes:
1. For a reSTART condition, or following a write cycle.
2. The minimum value delays the falling/rising edge of SDA away from SCL = 1 in order to avoid unwanted START and/or STOP
conditions.
3. In the Multibyte Write mode only, if accessed bytes are on two consecutive 8 bytes rows (5 address MSB are not constant)
the maximum programming time is doubled to 20ms.
Table 7. AC Characteristics
(T
A
= 0 to 70
°
C or –40 to 85
°
C; V
CC
= 4.5V to 5.5V or 2.5V to 5.5V)
DEVICE OPERATION
I
2
C Bus Background
The ST24/25x16 support the I
2
C protocol. This
protocol defines any device that sends data onto
the bus as a transmitter and any device that reads
the data as a receiver. The device that controls the
data transfer is known as the master and the other
as the slave. The master will always initiate a data
transfer and will provide the serial clock for syn-
chronisation. The ST24/25x16 are always slave
devices in all communications.
Start Condition.
START is identified by a high to
low transition of the SDA line while the clock SCL
is stable in the high state. A START condition must
precede any command for data transfer. Except
during a programming cycle, the ST24/25x16 con-
tinuously monitor the SDA and SCL signals for a
START condition and will not respond unless one
is given.
AI00825
0.8VCC
0.2VCC
0.7VCC
0.3VCC
Figure 4. AC Testing Input Output Waveforms
Input Rise and Fall Times
≤
50ns
Input Pulse Voltages
0.2V
CC
to 0.8V
CC
Input and Output Timing Ref.
Voltages
0.3V
CC
to 0.7V
CC
Table 8. AC Measurement Conditions
6/17
ST24/25C16, ST24/25W16
相關PDF資料 |
PDF描述 |
|---|---|
| ST24C16M1TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C16M1TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST24C16M3TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C16M3TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST24C16B1TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST24C16ML1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24C16ML3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24C16ML6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24D12 | 功能描述:固態繼電器-工業安裝 12A 240VAC Zero Cross RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| ST24D12/R | 制造商:Teledyne Relays 功能描述:OPTOCOUPL TRIAC AC-OUT 1-CH 600VDRM - Bulk 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY |
發布緊急采購，3分鐘左右您將得到回復。