- 您現在的位置：買賣IC網 > PDF目錄381095 > ST24C16M6TR (意法半導體) 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection PDF資料下載
參數資料
| 型號： | ST24C16M6TR |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| 中文描述： | 16千位串行I2C總線的EEPROM與用戶定義的塊寫保護 |
| 文件頁數： | 11/17頁 |
| 文件大小： | 126K |
| 代理商： | ST24C16M6TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Write Protection.
Data in the upper four blocks of
256 bytes of the memory may be write protected.
The memory is write protected between a boundary
address and the top of memory (address
7FFh).The boundary address is user defined by
writing it in the Block Address Pointer (location
7FFh).
The Block Address Pointer is an 8 bit EEPROM
register located at the address 7FFh. It is com-
posed by 4 MSBs Address Pointer, which defines
the bottom boundary address, and 4 LSBs which
must be programmed at ’0’. This Address Pointer
can therefore address a boundary by page of 16
bytes.
The block in which the Block Address Pointer de-
fines the boundary of the write protected memory
is defined by the logic level applied on the PB1 and
PB0 input pins:
– PB1 =’0’and PB0 =’0’ select block 4
– PB1 =’0’and PB0 =’1’ select block 5
– PB1 =’1’and PB0 =’0’ select block 6
– PB1 =’1’and PB0 =’1’ select block 7
The following sequence should be used to set the
Write Protection:
– write the data to be protected into the top of
the memory, up to, but not including, location
7FFh;
– select the block by hardwiring the signals PB0
& PB1;
– set the protection by writing the correct bottom
boundary address in the Address Pointer (4
MSBs of location 7FFh) with bit b2 (Protect
Flag) set to ’0’.
Note that for a correct fonctionality of the memory,
all the 4 LSBs of the Block Address Pointer must
also be programmed at ’0’. The area will be pro-
tected when the PRE input is taken High.
Remark:
The Write Protection is active if and only
if the PRE input pin is driven High and the bit 2 of
location 7FFh is set to ’0’. In all the other cases, the
memory Block will not be protected. While the PRE
input pin is read at ’0’ by the memory, the location
7FFh can be used as a normal EEPROM byte.
Caution:
Special attention must be used when
using the protect mode together with the Multibyte
Write mode (MODE input pin High). If the Multibyte
Write starts at the location right below the first byte
of the Write Protected area, then the instruction will
write over the first 7 bytes of the Write Protected
area. The area protected is therefore smaller than
the content defined in the location 7FFh, by 7 bytes.
This does not apply to the Page Write mode as the
address counter ’roll-over’ and thus cannot go
above the 16 bytes lower boundary of the protected
area.
S
S
BYTE WRITE
DEV SEL
BYTE ADDR
DATA IN
S
MULTIBYTE
AND
PAGE WRITE
DEV SEL
BYTE ADDR
DATA IN 1
DATA IN 2
AI00793
S
DATA IN N
ACK
ACK
ACK
R/W
ACK
ACK
ACK
R/W
ACK
ACK
Figure 9. Write Modes Sequence (ST24/25C16)
11/17
ST24/25C16, ST24/25W16
相關PDF資料 |
PDF描述 |
|---|---|
| ST24C16M1TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C16M1TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST24C16M3TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST25C16M3TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
| ST24C16B1TR | 16 Kbit Serial I2C Bus EEPROM with User-Defined Block Write Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST24C16ML1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24C16ML3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24C16ML6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24D12 | 功能描述:固態繼電器-工業安裝 12A 240VAC Zero Cross RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| ST24D12/R | 制造商:Teledyne Relays 功能描述:OPTOCOUPL TRIAC AC-OUT 1-CH 600VDRM - Bulk 制造商:Teledyne Relays 功能描述:SOLID STATE RELAY |
發布緊急采購，3分鐘左右您將得到回復。