- 您現在的位置：買賣IC網 > PDF目錄372289 > ST19-RFRDCS ST16-19RFRDCS CHIP SET INTERFACE SPECIFICATION PDF資料下載
參數資料
| 型號： | ST19-RFRDCS |
| 英文描述： | ST16-19RFRDCS CHIP SET INTERFACE SPECIFICATION |
| 中文描述： | 的ST16 - 19RFRDCS芯片組接口規范 |
| 文件頁數： | 7/21頁 |
| 文件大小： | 146K |
| 代理商： | ST19-RFRDCS |
1/15
This is a Preliminary Data on a new product now in development or undergoing evaluation. Details are subject to change with-
out noctice.
PRELIMINARY DATA
ST16-19RFRDCS
CHIP SET INTERFACE SPECIFICATION
1 FPGA & MCU INTERFACE
1.1 DESCRIPTION
The goal of this document is to provide a Hardware / Software interface specifications of the FPGA com-
ponent (Xilinx SPARTANXL XCS40XL-4PQ208C) used in the STMicroelectronics Contactless System.
The FPGA manages the communication between the MCU and the Analog Front End. This component
formats the frames in accordance with ISO 14443 type B standard.
1.2 PHYSICAL INTERFACE BETWEEN FPGA AND MCU
This corresponds to a classical memory interface between bidirectional Data bus, Selection signal, Read/
Write signal and a signal used to select either FIFOs or Control/Status registers access
1.2.1 Interface signals description
In order to simplify interface specification, the FPGA logic has been designed with the same accesses for
FIFOs and Control Registers. This is the reason why the read access chronogram show only one access
type (figure 1)
However, for write access chronogram, two access types are shown (figures 2 & 3).
MCU accesses are done in burst mode for the FIFOs, it is not useful to generate addresses. So, there is
no address bus for the MCU Interface. To address the different control registers, the two MSB bits from
the data bus must be used.
These control registers have to be setted during the first transmission each time the code is down loaded
in FPGA (start up of the reader) or when any parameter has to be modified. For later transmissions, the
control registers don’t need to be re initialised.
The control Register Description is available in table 2.
FSD_CHIPSET_B/0104VP2
相關PDF資料 |
PDF描述 |
|---|---|
| ST16 | CHIP SET INTERFACE SPECIFICATION |
| ST16010 | 1-Mbit (128K x 8) Static RAM |
| ST16010A | 1-Mbit (128K x 8) Static RAM |
| ST16012 | 18-Mbit QDR™-II SRAM 4-Word Burst Architecture |
| ST16018 | TRANSISTOR | BJT | NPN | 800V V(BR)CEO | 10A I(C) | TO-204AA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST19RFRDCS010 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CONTACTLESS READER CHIP SET |
| ST19RFRDCS910 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CONTACTLESS READER CHIP SET WITH ST92163MCU |
| ST19S020VCAR1400 | 功能描述:COMBO MICRO SD/NANO SIM R/A SMD 制造商:jae electronics 系列:ST19 包裝:剪切帶（CT） 零件狀態:在售 卡類型:組合 - microSD?，NANO SIM 針腳數:20 連接器類型:連接器和彈出器 插入，拆除方法:推入式，推出式 彈出器端:- 安裝類型:表面貼裝，直角 特性:板導軌，開關 板上高度:0.051"（1.30mm） 安裝特性:正常，標準 - 頂部 觸頭鍍層:金 觸頭鍍層厚度:12μin（0.30μm） 標準包裝:1 |
| ST19SF02 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Smartcard MCU With 2 KBytes of EEPROM |
| ST19SF04 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Smartcard MCU With 4 KBytes of EEPROM |
發布緊急采購，3分鐘左右您將得到回復。