- 您現在的位置：買賣IC網 > PDF目錄3762 > ST16C450IJ44-F (Exar Corporation)IC UART SINGLE 44PLCC PDF資料下載
參數資料
| 型號： | ST16C450IJ44-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 7/28頁 |
| 文件大小： | 0K |
| 描述： | IC UART SINGLE 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 1 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ST16C450
15
Rev. 4.20
LCR BIT-5 = logic 0, parity is not forced (normal default
condition)
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit
is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit
is forced to a logical 0 for the transmit and receive
data.
LCR
Parity selection
Bit-5
Bit-4
Bit-3
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity”1”
1
Forced parity “0”
LCR BIT-6:
When enabled the Break control bit causes a break
condition to be transmitted (the TX output is forced to
a logic 0 state). This condition exists until disabled by
setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (normal default
condition)
Logic 1 = Forces the transmitter output (TX) to a logic
0 for alerting the remote receiver to a line break
condition.
LCR BIT-7:
The internal baud rate counter latch and Enhance
Feature mode enable.
Logic 0 = Divisor latch disabled. (normal default
condition)
Logic 1 = Divisor latch and enhanced feature register
enabled.
Modem Control Register (MCR)
This register controls the interface with the modem or a
peripheral device.
MCR BIT-0:
Logic 0 = Force -DTR output to a logic 1. (normal
default condition)
Logic 1 = Force -DTR output to a logic 0.
MCR BIT-1:
Logic 0 = Force -RTS output to a logic 1. (normal default
condition)
Logic 1 = Force -RTS output to a logic 0.
MCR BIT-2:
Logic 0 = Set -OP1 output to a logic 1. (normal default
condition)
Logic 1 = Set -OP1 output to a logic 0.
MCR BIT-3:
Logic 0 = Set -OP2 output to a logic 1. (normal default
condition)
Logic 1 = Set -OP2 output to a logic 0.
MCR BIT-4:
Logic 0 = Disable loop-back mode. (normal default
condition)
Logic 1 = Enable local loop-back mode (diagnostics).
MCR BIT 5-7: Not used and set to “0”.
Line Status Register (LSR)
This register provides the status of data transfers
between. the ST16C450 and the CPU.
LSR BIT-0:
Logic 0 = No data in receive holding register. (normal
default condition)
Logic 1 = Data has been received and is saved in the
receive holding register.
LSR BIT-1:
Logic 0 = No overrun error. (normal default condition)
Logic 1 = Overrun error. A data overrun error occurred
in the receive shift register. This happens when addi-
tional data arrives while the RHR is full. In this case the
previous data in the shift register is overwritten. Note
that under this condition the data byte in the receive
shift register is not transfer into the RHR, therefore the
data in the RHR is not corrupted by the error.
LSR BIT-2:
Logic 0 = No parity error (normal default condition)
Logic 1 = Parity error. The receive character does not
have correct parity information and is suspect.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2750CMTR-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16V2550ILTR-F | IC UART FIFO 16B DUAL 32QFN |
| ATMEGA324PA-MUR | MCU AVR 32KB FLASH 20 MHZ 44QFN |
| ST78C36CJ44TR-F | IC UART FIFO 16B 44PLCC |
| XR16L2550IMTR-F | IC UART FIFO 16B DUAL 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C450IJ44TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C450IJ44TR-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450IP40 | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450IP40-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450IQ48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。