- 您現在的位置：買賣IC網 > PDF目錄372289 > ST16 (意法半導體) CHIP SET INTERFACE SPECIFICATION PDF資料下載
參數資料
| 型號： | ST16 |
| 廠商： | 意法半導體 |
| 英文描述： | CHIP SET INTERFACE SPECIFICATION |
| 中文描述： | 芯片組接口規范 |
| 文件頁數： | 8/21頁 |
| 文件大小： | 146K |
| 代理商： | ST16 |
2/15
ST16-19RFRDCS
FSD_CHIPSET_B/0104VP2
1.2.2 Interface signals definition
The signals used for the interface between FPGA & MCU, in transmission and reception, are:
Mic_Data(7:0):
Data bidirectional bus.
Mic_strb_b:
FPGA strobe signal (Activ low) used to sample the data.
This signal is sent by the MCU to the FPGA
Mic_RW:
Writing/Reading signal (’1’=reading, ’0’=writing).
This signal is sent by the MCU to the FPGA
Mic_Ctrl_Data:
Registers/FIFOs access signal (’1’ = Register access, ’0’ = FIFOs access).
This signal is sent by the MCU to the FPGA
Tx_start:
Transmission command, used to start data transmission from FIFO to output pin.
This signal is sent by the MCU to the FPGA
Tx_fifo_empty:
Signal used to indicate transmission fifo empty.
This signal is sent by the FPGA to the MCU
Rx_fifo_empty:
Signal used to indicate reception fifo empty.
This signal is sent by the FPGA to the MCU
Rx_irq_eof:
IRQ reception end.
This signal is sent by the FPGA to the MCU
1.3 FIFOS ACCESS
1.3.1 Transmission FIFO (cf figure 1)
At the end of a transmission (or during power-on), the FPGA sets the transmission FIFO pointers to zero.
This way, Tx_Fifo_Empty is validated, and so the software has to check that transmission FIFO is empty
before sending a new frame.
1.3.2 Reception FIFO (cf figures 2 & 3)
The reading pointer of reception FIFO is reset after each new frame received. It is impossible to get more
than one frame in the FIFO. Thus, after each interruption, data stored in the FIFO has to be read until val-
idation of Rx_Fifo_Empty signal.
WARNINGS: - Reception FIFO reading is done in "lookahead" mode. Bytes are read by the FPGA
in internal mode before being read by the MCU. Thus, the Rx_Fifo_Empty signal is valid just before
reading the last byte in the FIFO. FIFO reception has to be read once more when Rx_Fifo_Empty is
valid to get the last byte of the received frame.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16010 | 1-Mbit (128K x 8) Static RAM |
| ST16010A | 1-Mbit (128K x 8) Static RAM |
| ST16012 | 18-Mbit QDR™-II SRAM 4-Word Burst Architecture |
| ST16018 | TRANSISTOR | BJT | NPN | 800V V(BR)CEO | 10A I(C) | TO-204AA |
| STI409 | DIODE TVS 120V 600W BIDIR 5% SMB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST160/69/23 | 制造商:Block 功能描述:Control panel transformer, 160VA, 230V |
| ST1600/69/23 | 制造商:Block 功能描述:Control panel transformer, 1600VA, 230V |
| ST16002 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | BJT | NPN | 450V V(BR)CEO | 5A I(C) | TO-3 |
| ST16004 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | BJT | NPN | 450V V(BR)CEO | 5A I(C) | TO-3 |
| ST16006 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | BJT | NPN | 450V V(BR)CEO | 8A I(C) | TO-3 |
發布緊急采購，3分鐘左右您將得到回復。