參數資料
型號： SST89V54RD-33-C-PIE
廠商： Microchip Technology
文件頁數： 41/92頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 24KB FLASH 40PDIP
標準包裝： 9
系列： FlashFlex®
核心處理器： 8051
芯體尺寸： 8-位
速度： 33MHz
連通性： EBI/EMI，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，WDT
輸入/輸出數： 32
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 8K x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
振蕩器型： 外部
工作溫度： 0°C ~ 70°C
封裝/外殼： 40-DIP（0.600"，15.24mm）
包裝： 管件
2011 Silicon Storage Technology, Inc.
DS25087A
10/11
46
FlashFlex MCU
SST89V54RD2/RD / SST89V58RD2/RD
Not Recommended for New Designs
A Microchip Technology Company
Serial I/O
Full-Duplex, Enhanced UART
The device serial I/O port is a full-duplex port that allows data to be transmitted and received simulta-
neously in hardware by the transmit and receive registers, respectively, while the software is perform-
ing other tasks. The transmit and receive registers are both located in the Serial Data Buffer (SBUF)
special function register. Writing to the SBUF register loads the transmit register, and reading from the
SBUF register obtains the contents of the receive register.
The UART has four modes of operation which are selected by the Serial Port Mode Specifier (SM0 and
SM1) bits of the Serial Port Control (SCON) special function register. In all four modes, transmission is
initiated by any instruction that uses the SBUF register as a destination register. Reception is initiated
in mode 0 when the Receive Interrupt (RI) flag bit of the Serial Port Control (SCON) SFR is cleared
and the Reception Enable/ Disable (REN) bit of the SCON register is set. Reception is initiated in the
other modes by the incoming start bit if the REN bit of the SCON register is set.
Framing Error Detection
Framing Error Detection is a feature, which allows the receiving controller to check for valid stop bits in
modes 1, 2, or 3. Missing stops bits can be caused by noise in serial lines or from simultaneous trans-
mission by two CPUs.
Framing Error Detection is selected by going to the PCON register and changing SMOD0 = 1 (see Fig-
ure 17). If a stop bit is missing, the Framing Error bit (FE) will be set. Software may examine the FE bit
after each reception to check for data errors. After the FE bit has been set, it can only be cleared by
software. Valid stop bits do not clear FE. When FE is enabled, RI rises on the stop bit, instead of the
last data bit (see Figure 18 and Figure 19).
Figure 17:Framing Error Block Diagram
1255 F16.0
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
SMOD0
SMOD1
POF
GF1
GF0
PD
IDL
SCON
(98H)
PCON
(87H)
Set FE bit if stop bit is 0 (framing error) (SMOD0 = 1)
SM0 to UART mode control (SMOD0 = 0)
To UART framing error control
BOF
相關PDF資料
PDF描述
PIC18F25K22-E/ML MCU 8BIT 32KB FLASH 28QFN
PIC18LF25K22-E/ML MCU 32KB FLASH 1536B RAM 28QFN
PIC18F66J16T-I/PT IC PIC MCU FLASH 48KX16 64TQFP
VE-J50-IX-S CONVERTER MOD DC/DC 5V 75W
PIC24FJ32GA002T-I/ML IC PIC MCU FLASH 32KB 28QFN
相關代理商/技術參數
參數描述
SST89V54RD-33-C-QIF 功能描述:8位微控制器 -MCU 8-Bit 16K+8K Flash 33MHz 3/16-Bit Timer RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SST89V54RD-33-I-PI 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RD-33-I-PIE 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RD-33-I-QIF 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RDA 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*