- 您現在的位置：買賣IC網 > PDF目錄385855 > SP6121CN Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters PDF資料下載
參數資料
| 型號： | SP6121CN |
| 英文描述： | Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| 中文描述： | 低電壓，為第2A同步降壓PWM控制器的理想下至10A，占地面積小，DC - DC電源轉換器 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 358K |
| 代理商： | SP6121CN |
Date: 5/25/04
SP6121 Low Voltage, Synchronous Step Down PWM Controller Copyright 2004 Sipex Corporation
14
PCB layout plays a critical role in proper func-
tion of the converters and EMI control. In switch
mode power supplies, loops carrying high di/dt
give rise to EMI and ground bounces. The goal
of layout optimization is to identify these loops
and minimize them. It is also crucial on how to
connect the controller ground such that its op-
eration is not affected by noise. The following
guideline should be followed to ensure proper
operation.
1. A ground plane is recommended for minimiz-
ing noises, copper losses and maximizing heat
dissipation.
2. Begin the layout by placing the power compo-
nents first. Orient the power circuitry to achieve
a clean power flow path. If possible make all the
connections on one side of the PCB with wide,
copper filled areas.
3. Connect the ground of feedback divider and
compensation components directly to the GND
pin of the IC using a dedicated ground trace.
Then connect this pin as close as possible to the
ground of the output capacitor.
4. The V
CC
bypass capacitor should be right next
to the V
CC
and GND pins.
5. The trace connecting the feedback resistors to
the output should be short, direct and far away
from the switch node, and switching compo-
nents.
6. Minimize the trace between PDRV/NDRV
and the gates of the MOSFETs to reduce the
impedance driving the MOSFETs. This is espe-
cially important for the bottom MOSFET that
tends to turn on through its Miller capacitor
when the switch node swings high.
7. Minimize the loop composed of input capaci-
tors, top/bottom MOSFETs and Schottky diode.
This loop carries high di/dt current. Also in-
crease the trace width to reduce copper losses.
8. Maximize the trace width of the loop connect-
ing the inductor, output capacitors, Schottky
diode and bottom MOSFET.
9. I
SET
and I
SENSE
connections to Q1 for current
limiting must be make using Kelvin connec-
tions.
LAYOUT GUIDELINE
相關PDF資料 |
PDF描述 |
|---|---|
| SP6121EB | Demo Board Manual |
| SP6132H | High Voltage, 300KHz Synchronous PWM Controller |
| SP6132HEU | High Voltage, 300KHz Synchronous PWM Controller |
| SP6134 | Dual Supply Synchronous Buck Controller |
| SP6134CU | Dual Supply Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6121CN/TR | 功能描述:開關變換器、穩壓器與控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN-L | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN-L/TR | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121EB | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Sync Buck Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6122 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Voltage, Micro 8, PFET, Buck Controller Ideal for 1A to 5A, Small Footprint, DC-DC Power Converters |
發布緊急采購，3分鐘左右您將得到回復。