- 您現在的位置：買賣IC網 > PDF目錄385855 > SP6121 Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters PDF資料下載
參數資料
| 型號： | SP6121 |
| 英文描述： | Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| 中文描述： | 低電壓，為第2A同步降壓PWM控制器的理想下至10A，占地面積小，DC - DC電源轉換器 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 358K |
| 代理商： | SP6121 |
Date: 5/25/04
SP6121 Low Voltage, Synchronous Step Down PWM Controller Copyright 2004 Sipex Corporation
8
Inductor Selection
There are many factors to consider in selecting
the inductor including cost, efficiency, size and
EMI. In a typical SP6121 circuit, the inductor is
chosen primarily for value, saturation current
and DC resistance. Increasing the inductor value
will decrease output voltage ripple, but degrade
transient response. Low inductor values provide
the smallest size, but cause large ripple currents,
poor efficiency and more output capacitance to
smooth out the larger ripple current. The induc-
tor must also be able to handle the peak current
at the switching frequency without saturating,
and the copper resistance in the winding should
be kept as low as possible to minimize resistive
power loss. A good compromise between size,
loss and cost is to set the inductor ripple current
to be within 20% to 40% of the maximum output
current.
The switching frequency and the inductor oper-
ating point determine the inductor value as fol-
lows:
(max)
(max)
(max)
K
)
(
OUT
r
S
IN
OUT
IN
F
OUT
I
V
V
V
V
L
=
where;
F
S
= switching frequency
K
r
= ratio of the peak to peak inductor ripple
current to the maximum output current
The peak to peak inductor ripple current is:
L
F
V
V
V
(
V
I
S
IN
OUT
IN
OUT
PP
(max)
(max)
)
=
Once the required inductor value is selected, the
proper selection of core material is based on
peak inductor current and efficiency require-
ments. The core material must be large enough
not to saturate at the peak inductor current
2
(max)
PP
OUT
PEAK
I
I
I
+
=
and provide low core loss at the high switching
frequency. Low cost powdered iron cores have
a gradual saturation characteristic but can intro-
duce considerable ac core loss, especially when
the inductor value is relatively low and the
ripple current is high. Ferrite materials, on the
other hand, are more expensive and have an
abrupt saturation characteristic with the induc-
tance dropping sharply when the peak design
current is exceeded. Nevertheless, they are pre-
ferred at high switching frequencies because
they present very low core loss and the design
only needs to prevent saturation.
The power dissipated in the inductor is equal to
the sum of the core and copper losses. To mini-
mize copper losses, the winding resistance needs
to be minimized, but this usually comes at the
expense of a larger inductor. Core losses have a
more significant contribution at low output cur-
rent where the copper losses are at a minimum,
and can typically be neglected at higher output
currents where the copper losses dominate. Core
loss information is usually available from the
magnetic vendor.
The copper loss in the inductor can be calculated
using the following equation:
WINDING
R
RMS
L
Cu
L
I
P
2
)
(
)
(
=
where
I
L(RMS)
is the RMS inductor current that
can be calculated as follows:
I
L(RMS)
= I
OUT(max)
1 3 I
(
I
PP
)
2
OUT(max)
Output Capacitor Selection
The required ESR (Equivalent Series Resis-
tance) and capacitance drive the selection of the
type and quantity of the output capacitors. The
ESR must be small enough that both the resis-
tive voltage deviation due to a step change in the
load current and the output ripple voltage do not
exceed the tolerance limits expected on the
output voltage. During an output load transient,
the output capacitor must supply all the addi-
tional current demanded by the load until the
SP6121 adjusts the inductor current to the new
value. Therefore the capacitance must be large
enough so that the output voltage is held up
APPLICATION INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| SP6121CN | Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6121EB | Demo Board Manual |
| SP6132H | High Voltage, 300KHz Synchronous PWM Controller |
| SP6132HEU | High Voltage, 300KHz Synchronous PWM Controller |
| SP6134 | Dual Supply Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP612-10 | 制造商:Delphi Corporation 功能描述:TORSION SPRING |
| SP6121CN | 功能描述:開關變換器、穩壓器與控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN/TR | 功能描述:開關變換器、穩壓器與控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN-L | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN-L/TR | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。