- 您現在的位置：買賣IC網 > PDF目錄385855 > SP6121 Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters PDF資料下載
參數資料
| 型號： | SP6121 |
| 英文描述： | Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| 中文描述： | 低電壓，為第2A同步降壓PWM控制器的理想下至10A，占地面積小，DC - DC電源轉換器 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 358K |
| 代理商： | SP6121 |
Date: 5/25/04
SP6121 Low Voltage, Synchronous Step Down PWM Controller Copyright 2004 Sipex Corporation
11
well as provide typical curve of R
DS(ON)
versus
V
GS
. For 5V input, use the R
DS(ON)
specified at
4.5V V
GS
. At the time of this publication, ven-
dors, such as Fairchild, Siliconix and Interna-
tional Rectifier, have started to specify R
DS(ON)
at V
GS
less than 3V. This has provided necessary
data for designs in which these MOSFETs are
driven with 3.3V and made it possible to use
SP6121 in 3.3V only applications.
Thermal calculation must be conducted to en-
sure the MOSFET can handle the maximum
load current. The junction temperature of the
MOSFET, determined as follows, must stay
below the maximum rating.
JA
MOSFET
R
A
J
P
T
T
θ
(max)
(max)
(max)
+
=
,
where;
T
A(max)
= maximum ambient temperature
P
MOSFET(max)
= maximum power dissipation of
the MOSFET
R
θ
JA
= junction to ambient thermal resistance.
R
JA
of the device depends greatly on the board
layout, as well as device package. Significant
thermal improvement can be achieved in the
maximum power dissipation through the proper
design of copper mounting pads on the circuit
board. For example, in a SO-8 package, plac-
ing two 0.04 square inches copper pad di-
rectly under the package, without occupying
additional board space, can increase the maxi-
mum power from approximately 1 to 1.2W.
For DPAK package, enlarging the tap mount-
ing pad to 1 square inches reduces the R
θ
JA
from 96
°
C/W to 40
°
C/W.
Schottky Diode Selection
When paralleled with the bottom MOSFET, an
optional Schottky diode can improve efficiency
and reduce noise. Without this Schottky diode,
the body diode of the bottom MOSFET con-
ducts the current during the non-overlap time
when both MOSFETs are turned off. Unfortu-
nately, the body diode has high forward voltage
and reverse recovery problem. The reverse re-
covery of the body diode causes additional
switching noises when the diode turns off. The
Schottky diode alleviates this noise and addi-
tionally improves efficiency thanks to its low
forward voltage. The reverse voltage across the
diode is equal to input voltage, and the diode
must be able to handle the peak current equal to
the maximum load current.
The power dissipation of the Schottky diode is
determined by
P
DIODE
= 2V
F
I
OUT
T
NOL
F
S
where;
T
NOL
= non-overlap time between PDRV and
NDRV.
V
F
= forward voltage of the Schottky diode.
SP6121
C2
C1
R1
COMP
Figure 4. The RC network connected to the COMP pin
provides a pole and a zero to control loop.
Loop Compensation Design
The goal of loop compensation is to manipulate
loop frequency response such that its gain crosses
over 0db at a slope of -20db/dec. The SP6121
has a trans-conductance error amplifier and re-
quires the compensation network to be con-
nected between the COMP pin and ground, as
shown in Figure 4.
The first step of compensation design is to pick
the loop crossover frequency. High crossover
frequency is desirable for fast transient response,
but often jeopardize the system stability. Cross-
over frequency should be higher than the ESR
zero but less than 1/5 of the switching fre-
quency. The ESR zero is contributed by the ESR
APPLICATIONS INFORMATION: Continued
相關PDF資料 |
PDF描述 |
|---|---|
| SP6121CN | Low Voltage, Synchronous Step Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6121EB | Demo Board Manual |
| SP6132H | High Voltage, 300KHz Synchronous PWM Controller |
| SP6132HEU | High Voltage, 300KHz Synchronous PWM Controller |
| SP6134 | Dual Supply Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP612-10 | 制造商:Delphi Corporation 功能描述:TORSION SPRING |
| SP6121CN | 功能描述:開關變換器、穩壓器與控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN/TR | 功能描述:開關變換器、穩壓器與控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN-L | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6121CN-L/TR | 功能描述:電壓模式 PWM 控制器 Low Voltage, 8 Pin Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。