- 您現在的位置：買賣IC網 > PDF目錄385854 > SP301 12-Bit, 12MHz CCD/CIS SIGNAL PROCESSOR PDF資料下載
參數資料
| 型號： | SP301 |
| 英文描述： | 12-Bit, 12MHz CCD/CIS SIGNAL PROCESSOR |
| 中文描述： | 12位，12MHz的防治荒漠化公約/ CIS信號處理器 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 199K |
| 代理商： | SP301 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
13
VSP3010
the bus coupling back high frequency noise. In addition,
resistors in series with each data line may help minimize the
surge current. Their use depends on the capacitive loading
seen by the converter. As the output levels change from low
to high and high to low, values in the range of 100
to 200
will limit the instantaneous current the output stage has to
provide for recharging the parasitic capacitances.
GROUNDING, BYPASSING, AND POWER SUPPLY
RECOMMENDATIONS
Proper grounding, bypassing, short lead length and the use
of ground planes are particularly important for high fre-
quency designs. Multi-layer PC boards are recommended
for the best performance since they offer distinct advantages
such as minimizing ground impedance, separation of signal
layers by ground layers, etc. It is recommended that analog
and digital ground pins of the VSP3010 be joined together
at the IC and connected only to the analog ground of the
system.
The VSP3010 has analog and digital supply pins, however,
the converter should be treated as an analog component and
all supply pins should be powered by the analog supply. This
will ensure the most consistent results since digital supply
lines often carry high levels of noise that would otherwise be
coupled into the converter and degrade the achievable per-
formance.
As the result of the high operation speed, the converter also
generates high frequency current transients and noise that
are fed back into the supply and reference lines. This
requires that the supply and reference pins be sufficiently
bypassed. Figure 3 shows the recommended decoupling
schemes for the entire chip. In most cases, 0.1
μ
F ceramic
chip capacitors are adequate to keep the impedance low over
the wide frequency range. Their effectiveness largely de-
pends on the proximity to the individual supply pin.
When the VSP3010 is powered on, it will be initialized as a
3-channel CCD, 1V internal (2V full scale) reference mode
with analog gain of 1. This mode is commonly used for CCD
scanner applications. The calibration procedure is done at the
very beginning of the scan. Once calibration is done, regis-
ters on VSP3010 will keep this information (offset and gain
for each channel) during the operation.
To calibrate the VSP3010, use the following procedure:
Step 1: Set the VSP3010 to the proper mode.
Step 2: Set analog PGA gain to 1 (code: 00
H
) and offset to
0mV (code: C0
H
).
Step 3: Scan a dark line.
Step 4: Calculate the pixel offsets according to the ADC
output.
Step 5: Readjust input Offset Registers.
Step 6: Scan a white line.
Step 7: Calculate gain. It will be the ADC full scale divided
by the ADC output when the white line is scanned.
Step 8: Set the Gain Register. If the ADC output is not
close to full scale, go back to Step 3. The calibration
is complete if the output is close to full scale.
相關PDF資料 |
PDF描述 |
|---|---|
| SP3232E | True +3.0V to +5.5V RS-232Transceivers(標準+3.0V 至 +5.5V RS-232收發器（2發2收）) |
| SP3243E | Intelligent +3.0V to +5.5V RS-232 Transceivers(智能+3.0V 至 +5.5V RS-232收發器（3發5收）) |
| SP3483 | 3.3V Low Power Slew Rate Limited Half-Duplex RS-485/RS-422 Transceiver(3.3V,低功耗，轉換速率限制，半雙工RS-485/RS-422收發器) |
| SP3483CN | +3.3V Low Power Slew Rate Limited Half-Duplex RS-485 Transceiver |
| SP3483CP | +3.3V Low Power Slew Rate Limited Half-Duplex RS-485 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP-301 | 功能描述:烙鐵 500W SOLDER POT 120 VOLT RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| SP3010 | 功能描述:烙鐵 SOLDERING TOOL RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| SP3010 | 制造商:3M Electronic Products Division 功能描述:Tools Soldering |
| SP3010_11 | 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:SP3010 Series 0.45pF Rail Clamp Array |
| SP3010-04UTG | 功能描述:TVS二極管陣列 4 Ch 8kV 6V .45pF RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
發布緊急采購，3分鐘左右您將得到回復。