- 您現在的位置：買賣IC網 > PDF目錄373427 > SMH4811A (Electronic Theatre Controls, Inc.) DISTRIBUTED POWER HOT SWAP CONTROLLER PDF資料下載
參數資料
| 型號： | SMH4811A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | DISTRIBUTED POWER HOT SWAP CONTROLLER |
| 中文描述： | 分布式電源熱插拔控制器 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 358K |
| 代理商： | SMH4811A |
6
SMH4811A
Preliminary
2044 6.1 2/8/01
SUMMIT MICROELECTRONICS, Inc.
FUNCTIONAL DESCRIPTION
GENERAL OPERATION
The SMH4811A is an integrated power controller for hot
swappable add-in cards. The device operates from a wide
supply range and generates the signals necessary to drive
an isolated output DC/DC converter. As a typical add-in
board is inserted into the powered backplane physical
connections must first be made with the chassis to dis-
charge any electrostatic voltage potentials. The board
then contacts the long pins on the backplane that provide
power and ground. As soon as power is applied the device
starts up, but does not immediately apply power to the
output load. Under-voltage and over-voltage circuits
inside the controller check to see that the input voltage is
within a user-specified range, and pin detection signals
determine whether the card is seated properly.
These requirements must be met for a Pin Detect Delay
period of t
PDD
, after which time the hot-swap controller
enables VGATE to turn on the external power MOSFET
switch. The VGATE output is current limited to I
VGATE
,
allowing the slew rate to be easily modified using external
passive components. During the controlled turn-on period
the V
DS
of the MOSFET is monitored by the DRAIN
SENSE input. When the drain sense drops below 2.5V,
and VGATE gets above V
DD
–
V
GT
, the power good output
can turn on the DC/DC controller. A Power Good Enable
input may be used to activate or deactivate an output load.
Steady state operation is maintained as long as all condi-
tions are normal. Any of the following events may cause
the device to disable the DC/DC controller by shutting
down the power MOSFET: an under-voltage or over-
voltage condition on the host power supply; an over-
current event detected on the CBSENSE input; a failure of
the power MOSFET sensed via the DRAIN SENSE pin;
the pin detect signals becoming invalid; or the master
enable (EN/TS) falling below 2.5V. The SMH4811A may
be configured so that after any of these events occur the
VGATE output shuts off and either latches into an off state
or recycles power after a cooling down period, t
CYC
.
Powering V
DD
The SMH4811A contains a shunt regulator on the V
DD
pin
that prevents the voltage from exceeding 12V. It is
necessary to use a dropper resistor (R
D
) between the host
power supply and the V
DD
pin in order to limit current into
the device and prevent possible damage. The dropper
resistor allows the device to operate across a wide range
of system supply voltages, and also helps protect the
device against common-mode power surges. Refer to the
Applications Section for help on calculating the R
D
resis-
tance value.
System Enables
There are several enabling inputs, which allow a host
system to control the SMH4811A. The Pin Detect pins
(PD1# & PD2#) are two active low enables that are
generally used to indicate that the add-in circuit card is
properly seated. This is typically done by clamping the
inputs to V
SS
through the implementation of an injector
switch, or alternatively through the use of a staggered pins
at the card-cage interface. Two shorter pins arrayed at
opposite ends of the connector force the card to be fully
seated (not canted) before both pin detects are enabled.
Care must be taken not to exceed the maximum voltage
rating of these pins during the insertion process. Refer to
details in the Applications Section for proper circuit imple-
mentation.
The EN/TS input provides an active high comparator input
that may be used as a master enable or temperature
sense input. These inputs must be held low for a period of
t
PDD
before a power-up sequence may be initiated.
Under-/Over-Voltage Sensing
The Under-Voltage (UV) and Over-Voltage (OV) inputs
provide a set of comparators that act in conjunction with an
external resistive divider ladder to sense when the host
supply voltage exceeds the user defined limits. If the input
to the UV pin rises above 2.5V, or the input to the OV pin
falls below 2.5V for a period of t
PDD
, the power-up se-
quence may be initiated. The t
PDD
filter helps prevent
spurious start-up sequences while the card is being in-
serted. If UV falls below 2.5V or OV rises above 2.5V, the
PG and VGATE outputs will be shut down immediately.
Figure 1. Under-/Over-Voltage Filter Timing
2044 Fig01 5.0
OV / UV
FAULT#
t
UOFLTR
2.5V
相關PDF資料 |
PDF描述 |
|---|---|
| SMH4811AG | DISTRIBUTED POWER HOT SWAP CONTROLLER |
| SMH4811AS | DISTRIBUTED POWER HOT SWAP CONTROLLER |
| SMH | LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS |
| SMJ27C010A | UVEPROM |
| SMJ27C010A-12 | UVEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMH4811A_09 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Programmable Distributed Power Hot-Swap Controller for High-Availability Systems |
| SMH4811AG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER |
| SMH4811AS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DISTRIBUTED POWER HOT SWAP CONTROLLER |
| SMH4812 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Distributed Power Hot-Swap Controller |
| SMH4812_09 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Distributed Power Hot-Swap Controller |
發布緊急采購，3分鐘左右您將得到回復。