- 您現在的位置：買賣IC網 > PDF目錄365566 > SiI3726CBHU (Silicon Image, Inc.) SATA Port Multiplier PDF資料下載
參數資料
| 型號： | SiI3726CBHU |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | SATA Port Multiplier |
| 中文描述： | SATA端口倍增器 |
| 文件頁數： | 8/41頁 |
| 文件大?。?/td> | 375K |
| 代理商： | SII3726CBHU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
SiI3726 SATA Port Multiplier
Data Sheet
SATA Ports
Silicon Image, Inc.
2006 Silicon Image, Inc.
SiI-DS-0121-C1
8
The host port supports the SATA-II speed of 3 Gbps and auto-negotiates to 1.5 Gbps to interface with SATA-I host
controllers. The device ports operate at SATA-II speeds of 3 Gbps or auto-negotiate to 1.5 Gbps. All ports support
hot plug and extended (48 bit LBA) drive capability.
LED Modes
Device/Host LED Modes
Table 1 shows the device or host LED modes and descriptions. The mode is determined by the LED_MODE pin
(pin A3). LED pins are open-drain and sink current up to 12mA in their low voltage active state (LED On), or are
high impedance in their high voltage non-active state (LED Off). These signals will operate with an external pull-
up resistor and LED.
Each activity will turn on or off LED0 for approximately 70ms. The blinking rate is approximately 400ms on and
400ms off.
Table 1: Device or Host LED Modes and Descriptions
LED_MODE
0 (PC mode)
0 (PC mode)
0 (PC mode)
1 (Enterprise mode)
1 (Enterprise mode)
LED1
Off
On
Blink
Off
On
LED0
Off
Off
Blink
Off
Off
Description
Power on, no device attached
PHY communication established, (activity = LED0 On)
Error
Power on, no device
Error
System LED Modes
Table 2 shows the System LED modes and their descriptions.
Table 2: System LED Modes and Descriptions
Signal
LED_S0
Description
EEPROM load error
On: Loading error
Off: No loading errors
System ready
On: System is ready
Off: System is not ready
System error
On: System error
Off: No system errors
LED_S1
LED_S2
In normal operation, if system reset is released, LED_S3 will turn-on while the firmware loads into the SiI 3726
SATA Port Multiplier (~ 1 second). When the firmware load is complete, LED_S1 will turn-on indicating the system
is ready to be used.
相關PDF資料 |
PDF描述 |
|---|---|
| SII3811PB | SteelVine⑩ Device Bridge |
| SII4723 | SATA to 2-Port 3Gb/s SATA SteelVine Storage Processor |
| SII4726 | SATA to 5-Port SATA Device SteelVine⑩ Storage Processor |
| SII504 | Digital Video Processor |
| SII5723PB | SteelVine⑩ Storage Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII3811PB | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:SteelVine⑩ Device Bridge |
| SII400N12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:NPT IGBT Modules |
| SII400S12 | 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:絕緣柵雙極型晶體管（IGBT）Isolated Gate Bipolar Transistor (IGBTs)，SPT技術的IGBT模塊SPT IGBT Modules (Soft Punch Through Technology)。 |
| SII4723 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:SATA to 2-Port 3Gb/s SATA SteelVine Storage Processor |
| SII4726 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:SATA to 5-Port SATA Device SteelVine⑩ Storage Processor |
發布緊急采購，3分鐘左右您將得到回復。