- 您現在的位置：買賣IC網 > PDF目錄368620 > SI8250-IM (SILICON LABORATORIES) DIGITAL POWER CONTROLLER PDF資料下載
參數資料
| 型號： | SI8250-IM |
| 廠商： | SILICON LABORATORIES |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | DIGITAL POWER CONTROLLER |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, QCC28 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, QFN-28 |
| 文件頁數： | 22/30頁 |
| 文件大?。?/td> | 932K |
| 代理商： | SI8250-IM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Si8250/1/2
22
Preliminary Rev. 0.8
In both cases, the bias supplies must be filtered using low ESR/ESL capacitors placed close to the IC pins.
Thick copper traces should be connected to the bias pins (VDD, VDDA) and the ground pins (GND, GNDA) to
reduce resistance and inductance. The copper routings from the drivers to the FETs should be kept short and wide,
especially in very high frequency applications, to reduce inductance of the traces so that the drive signals can be
kept clean.
Connections between VSENSE and the output voltage must be kept absolutely as short as possible to minimize
inductance and parasitic ringing effects. It is best to locate the Si8250/1/2 as close to the output voltage terminal as
possible and use a Kelvin connection to ensure to difference in ground potential between the Si8250/1/2 and the
output voltage ground return.
Most applications will require access to the debug pins. These pins are susceptible to damage from electrostatic
discharge (ESD). It is therefore recommended the debug circuit interface use the input protection circuitry shown in
Figure 11.
Figure 11. Debug Interface Pin Protection Circuit
DEBUG
CONNECTOR
10
10
Si8250/1/2
Debug Pins
(C2D, C2CK)
2
相關PDF資料 |
PDF描述 |
|---|---|
| SI8250-IQ | DIGITAL POWER CONTROLLER |
| SI8401DB-T1 | P-Channel 20-V (D-S) MOSFET, Low-Threshold |
| SI8401DB-T1-E3 | P-Channel 20-V (D-S) MOSFET, Low-Threshold |
| SI8401DB | Single P-Channel MOSFET; |
| SI8402DB | 20-V N-Channel 1.8-V (G-S) MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI8250-IMR | 制造商:Silicon Laboratories Inc 功能描述:VOLT SUPERVISOR PWR SUPPLY 0.05V TO 0.8V 28QFN - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC DIGITAL PWR CONTROLLER 32LQFP 制造商:Silicon Laboratories Inc 功能描述:32K 28 Pin SMPS Controller |
| SI8250-IQ | 功能描述:電壓監測器/監控器 SMPS Controller RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| SI8250-IQR | 制造商:Silicon Laboratories Inc 功能描述:VOLT SUPERVISOR PWR SUPPLY 0.05V TO 0.8V 32LQFP - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC DIGITAL PWR CONTROLLER 32LQFP 制造商:Silicon Laboratories Inc 功能描述:32K 32 Pin SMPS Controller |
| SI8251 | 制造商:SILABS 制造商全稱:SILABS 功能描述:DIGITAL POWER CONTROLLER |
| SI8251-IM | 功能描述:功率驅動器IC SMPS Controller RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。