- 您現在的位置：買賣IC網 > PDF目錄8977 > SI5338P-A-GM (Silicon Laboratories Inc)IC CLK GEN I2C BUS PROG 24QFN PDF資料下載
參數資料
| 型號： | SI5338P-A-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 24/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK GEN I2C BUS PROG 24QFN |
| 標準包裝： | 490 |
| 系列： | MultiSynth™ |
| 類型： | * |
| PLL： | 是 |
| 輸入： | CML，HCSL，HSCL，LVDS，LVPECL，晶體 |
| 輸出： | CMOS，HCSL. HSTL. LVDS. LVPECL. SSTL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:4 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 350MHz |
| 除法器/乘法器： | 是/是 |
| 電源電壓： | 1.71 V ~ 3.63 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN（4x4） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Si5338
30
Rev. 1.3
5. I2C Interface
Configuration and operation of the Si5338 is controlled
by reading and writing to the RAM space using the I2C
interface. The device operates in slave mode with 7-bit
addressing
and
can
operate
in
Standard-Mode
(100 kbps) or Fast-Mode (400 kbps) and supports burst
data transfer with auto address increments.
The I2C bus consists of a bidirectional serial data line
(SDA) and a serial clock input (SCL) as shown in
Figure 21. Both the SDA and SCL pins must be
connected to the VDD supply via an external pull-up as
recommended by the I2C specification.
Figure 21. I2C and Control Signals
The 7-bit device (slave) address of the Si5338 consists
of a 6-bit fixed address plus a user-selectable LSB bit as
shown in Figure 22. The LSB bit is selectable using the
optional I2C_LSB pin which is available as an ordering
option for applications that require more than one
Si5338 on a single I2C bus. Devices without the
I2C_LSB pin option have a fixed 7-bit address of 70h
addresses are also possible. See Table 17 for details on
device ordering information with the optional I2C_LSB
pin.
Figure 22. Si5338 I2C Slave Address
Data is transferred MSB first in 8-bit words as specified
by the I2C specification. A write command consists of a
7-bit device (slave) address + a write bit, an 8-bit
register address, and 8 bits of data as shown in
Figure 23. A write burst operation is also shown where
every additional data word is written using an auto-
incremented address.
Figure 23. I2C Write Operation
A read operation is performed in two stages. A data
write is used to set the register address, then a data
read is performed to retrieve the data from the set
address. A read burst operation is also supported. This
is shown in Figure 24.
Figure 24. I2C Read Operation
AC and dc electrical specifications for the SCL and SDA
pins are shown in Table 15. The timing specifications
and timing diagram for the I2C bus are compatible with
the I2C-Bus Standard. SDA timeout is supported for
compatibility with SMBus interfaces.
The I2C bus can be operated at a bus voltage of 1.71 to
3.63 V and is 3.3 V tolerant. If a bus voltage of less than
2.5 V is used, register 27[7] = 1 must be written to
maintain compatibility with the I2C bus standard.
Control
I2C_LSB
I2C_LSB/PDEC/FDEC
OEB/PINC/FINC
0/1
SCL
SDA
I
2C Bus
VDD
Slave Address
(with I2C_LSB Option)
1 1 1 0 0 0 0/1
I2C_LSB pin
0
1
2
3
4
5
6
Slave Address
(without I2C_LSB Option)
1 1 1 0 0 0
0
1
2
3
4
5
6
1 – Read
0 – Write
A – Acknowledge (SDA LOW)
N – Not Acknowledge (SDA HIGH)
S – START condition
P – STOP condition
From slave to master
From master to slave
Write Operation – Single Byte
S
0 A Reg Addr [7:0]
Slv Addr [6:0]
A Data [7:0]
P
A
Write Operation - Burst (Auto Address Increment)
Reg Addr +1
S
0 A Reg Addr [7:0]
Slv Addr [6:0]
A Data [7:0]
P
A
1 – Read
0 – Write
A – Acknowledge (SDA LOW)
N – Not Acknowledge (SDA HIGH)
S – START condition
P – STOP condition
From slave to master
From master to slave
Read Operation – Single Byte
S
0 A Reg Addr [7:0]
Slv Addr [6:0]
A P
Read Operation - Burst (Auto Address Increment)
Reg Addr +1
S
1 A
Slv Addr [6:0]
Data [7:0]
P
N
S
0 A Reg Addr [7:0]
Slv Addr [6:0]
A P
S
1 A
Slv Addr [6:0]
Data [7:0]
A
P
N
Data [7:0]
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2642CMS-16#PBF | IC DAC 16BIT VOUT 10-MSOP |
| VI-B0Z-MY-F3 | CONVERTER MOD DC/DC 2V 20W |
| MS27497T18B96SA | CONN RCPT 9POS WALL MNT W/SCKT |
| LTC2642CDD-16#PBF | IC DAC 16BIT VOUT 10-DFN |
| AD5555CRUZ | IC DAC 14BIT DUAL SRL IN 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI5338P-A-GMR | 功能描述:時鐘發生器及支持產品 I2C Program Clk Gen 0.16-350MHz 4Clk In RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| SI5338P-B01199-GMR | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Tape and Reel |
| SI5338P-B01574-GM | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Bulk |
| SI5338P-B01574-GMR | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Tape and Reel |
| SI5338P-B01597-GMR | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。