- 您現在的位置：買賣IC網 > PDF目錄16210 > SI3056DC2-EVB (Silicon Laboratories Inc)DAUGHTERCARD DAA SI3056/SI3010 PDF資料下載
參數資料
| 型號： | SI3056DC2-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 33/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | DAUGHTERCARD DAA SI3056/SI3010 |
| 標準包裝： | 1 |
| 主要目的： | 電信，數據采集裝置（DAA） |
| 已用 IC / 零件： | Si3056 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
Si3056
Si3018/19/10
Rev. 1.05
39
SRC[3:0] bits (Register 7, bits 3:0) must be
programmed with the proper sample rate value before
the sampled line data is valid. The SCLK pin of the
slave is a no connect in this configuration.
The delay between FSYNC input and delayed frame
sync output (RGDT/FSD/M1) is 16 SCLK periods. The
RGDT/FSD/M1 output has a waveform identical to the
FSYNC signal in serial mode 0. In addition, the LSB of
SDO is set to 0 by default for all devices in serial
mode 2.
5.28. Power Management
The Si3056 supports four basic power management
operation modes. The modes are normal operation,
reset operation, sleep mode, and full powerdown mode.
PDN and PDL bits (Register 6) control the power
management modes.
On powerup, or following a reset, the Si3056 is in reset
operation. The PDL bit is set, and the PDN bit is
cleared. The Si3056 is operational, except for the
isolation link. No communication between the Si3056
and line-side device can occur during reset operation.
Bits associated with the line-side device are not valid in
this mode.
In typical applications, the DAA will predominantly be
operated in normal mode. In this mode, the PDL and
PDN bits are cleared. The Si3056 is operational and the
isolation link is passing information between the Si3056
and the line-side device.
The Si3056 supports a low-power sleep mode to
support ring validation and wake-on-ring features. The
clock generator registers 7, 8, and 9 must be
programmed with valid, non-zero values and the PDL
bit must be clear before enabling sleep mode. The PDN
bit must then be set. When the Si3056 is in sleep mode
the MCLK signal must remain active. In low-power
sleep mode with MCLK active, the Si3056 is non-
functional except for the isolation link and the RGDT
signal. To take the Si3056 out of sleep mode, pulse the
reset pin (RESET) low.
In summary, the powerdown/up sequence for sleep
mode is as follows:
1. Ensure that Registers 7, 8, and 9 have valid non-
zero values, and ensure the PDL bit (Register 6, bit
4) is cleared.
2. Set the PDN bit (Register 6, bit 3).
3. The device is now in sleep mode. MCLK must stay
active.
4. To exit sleep mode, reset the Si3056 by pulsing the
RESET pin.
5. Program registers to desired settings.
The Si3056 also supports an additional powerdown
mode. When both the PDN (Register 6, bit 3) and PDL
(Register 6, bit 4) bits are set, the chipset enters a
complete powerdown mode and draws negligible
current (deep sleep mode). Turn off the PLL2 before
entering deep sleep mode (i.e., set Register 9 to 0 and
then Register 6 to 0x18). In this mode, the Si3056 is
non-functional. Normal operation is restored by the
same process for taking the DAA out of sleep mode.
5.29. Calibration
The Si3056 initiates two auto-calibrations by default
when the device goes off-hook or experiences a loss in
line power. A 17 ms resistor calibration is performed to
allow circuitry internal to the DAA to adjust to the exact
line conditions present at that time. This resistor
calibration can be disabled by setting the RCALD bit
(Register 25, bit 5). A 256 ms ADC calibration is also
performed to remove offsets that might be present in the
on-chip A/D converter which could affect the A/D
dynamic range. The ADC auto-calibration is initiated
after the DAA dc termination stabilizes, and the resistor
calibration completes. Because large variations in line
conditions and line card behavior exist, it could be
beneficial to use manual calibration instead of auto-
calibration.
Execute manual ADC calibration as close as possible to
256 ms before valid transmit/receive data is expected.
Take the following steps to implement manual ADC
calibration:
1. The CALD (auto-calibration disable—Register 17) bit
must be set to 1.
2. The MCAL (manual calibration) bit must be toggled
to 1 and then 0 to begin and complete the
calibration.
3. The calibration is completed in 256 ms.
5.30. In-Circuit Testing
With the Si3056’s advanced design the designer can
determine system functionality during production line
tests, and during support for end-user diagnostics. Four
loopback modes allow thorough coverage of system
components. Four of the test modes require a line-side
power source. Although a standard phone line can be
used, the test circuit in Figure 1 on page 6 is adequate.
In addition, an off-hook sequence must be performed to
connect the power source to the line-side device.
For the start-up loopback test mode, line-side power is
not necessary and no off-hook sequence is required.
The start-up test mode is enabled by default. When the
PDL bit (Register 6, bit 4) is set (the default case), the
line-side is in a powerdown mode and the DSP-side is
in a digital loop-back mode. Data received on SDI
相關PDF資料 |
PDF描述 |
|---|---|
| CW252016-56NG | INDUCTOR 56NH 1008 SMD |
| SI3056DC1-EVB | DAUGHTERCARD DAA SI3056/SI3019 |
| GBM31DCAI | CONN EDGECARD 62POS R/A .156 SLD |
| SI3050PPT2-EVB | BOARD EVAL FOR DAA SI3050/SI3008 |
| CW252016-47NG | INDUCTOR 47NH 1008 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Si3056DC3-EVB | 功能描述:子卡和OEM板 Global DAA Daughter Card Only RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| Si3056DC-EVB | 功能描述:子卡和OEM板 Global DAA Daughter Card Only RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| Si3056-D-FS | 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3056-D-FSR | 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3056-D-ZS3R | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET 56KBPS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。