參數資料
型號: SI3056DC2-EVB
廠商: Silicon Laboratories Inc
文件頁數: 27/94頁
文件大?。?/td> 0K
描述: DAUGHTERCARD DAA SI3056/SI3010
標準包裝: 1
主要目的: 電信,數據采集裝置(DAA)
已用 IC / 零件: Si3056
已供物品: 板,CD
Si3056
Si3018/19/10
Rev. 1.05
33
line data. The host processor must detect the
presence of this tone.
2. The DAA must then check for another parallel device
on the same line. This is accomplished by briefly
going on-hook, measuring the line voltage, and then
returning to an off-hook state.
a. Set the CALD bit (Register 17, bit 5) to disable
the calibration that automatically occurs when
going off-hook.
b. Set the RCALD bit (Register 25, bit 5) to disable
the resistor calibration from occurring when
going off-hook.
c. Set the FOH[1:0] bits (Register 31, bits 6:5) to 11
to reduce the off-hook counter time to 8 ms.
d. Clear the OH bit (or drive the OFHK pin to the
inactive state) to put the DAA in an on-hook
state. The RXM bit (Register 19, bit 3) may also
be set to mute the receive path.
e. Read the LVS bits to determine the state of the
line.
If the LVS bits read the typical on-hook line
voltage, then no parallel devices are active on
the line and CID data reception can be
continued.
If the LVS bits read well below the typical on-
hook line voltage, then one or more devices are
present and active on the same line that are not
compliant with Type II CID. Do not continue CID
data reception.
f. Set the OH bit to 1 (or drive the OFHK pin to the
active state) to return to an off-hook state. After
returning to an off-hook state and waiting 8 ms
for the off-hook counter, normal data
transmission and reception can proceed. If a
non-compliant parallel device is present, then a
reply tone is not sent by the host tone generator
and the CO does not proceed with sending the
CID data. If all devices on the line are Type II CID
compliant, then the host must mute its upstream
data output to avoid propagation of its reply tone
and the subsequent CID data. After muting its
upstream data output, the host processor should
then return an acknowledgement (ACK) tone to
the CO to request the transmission of the CID
data.
3. The CO then responds with the CID data and the
host processor unmutes the upstream data output
and continues with normal operation.
4. The muting of the upstream data path by the host
processor mutes the handset in a telephone
application so the user cannot hear the
acknowledgement tone and CID data being sent.
5. The CALD and RCALD bits can be cleared to re-
enable the automatic calibration when going off-
hook. The FOH[1:0] bits also can be programmed to
01 to restore the default off-hook counter time.
Because of the nature of the low-power ADC, the data
presented on SDO could have up to a 10% dc offset.
The caller ID decoder must either use a high pass or a
band pass filter to accurately retrieve the caller ID data.
相關PDF資料
PDF描述
CW252016-56NG INDUCTOR 56NH 1008 SMD
SI3056DC1-EVB DAUGHTERCARD DAA SI3056/SI3019
GBM31DCAI CONN EDGECARD 62POS R/A .156 SLD
SI3050PPT2-EVB BOARD EVAL FOR DAA SI3050/SI3008
CW252016-47NG INDUCTOR 47NH 1008 SMD
相關代理商/技術參數
參數描述
Si3056DC3-EVB 功能描述:子卡和OEM板 Global DAA Daughter Card Only RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
Si3056DC-EVB 功能描述:子卡和OEM板 Global DAA Daughter Card Only RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
Si3056-D-FS 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3056-D-FSR 功能描述:電信線路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3056-D-ZS3R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET 56KBPS - Tape and Reel