參數資料
型號： SI2401FS08-EVB
廠商： Silicon Laboratories Inc
文件頁數： 17/76頁
文件大?。?/td> 0K
描述： BOARD EVAL SI2401 + SI3008
標準包裝： 1
系列： ISOmodem®
主要目的： 電信，數據采集裝置（DAA）
已用 IC / 零件： SI2401
已供物品： 板，CD
Si2401
24
Rev. 1.0
5. AT Command Set
The controller provides several vital functions including
AT command parsing, DAA control, connect sequence
control, DCE protocol control, intrusion detection,
parallel phone off-hook detection, escape control, caller
ID control and formatting, ring detect, DTMF control, call
progress monitoring, and HDLC framing. The controller
also writes to the control registers that configure the
modem. Virtually all interaction between the host and
the modem is done via the controller. The controller
uses AT (ATtention) commands and S-Registers to
configure and control the modem.
The modem has two modes of operation: command
mode and data mode. The Si2401 is asynchronous in
both command mode and data mode. The modem is in
command mode at powerup, after a reset, before a
connection is made, after a connection is dropped, and
during a connection after successfully “Escaping” from
the data mode back to the command mode using one of
the methods previously described. The following section
describes the AT command set available in command
mode.
The Si2401 supports a subset of the typical modem AT
command set since it is intended for use with a
dedicated microcontroller instead of general terminal
applications. AT commands begin with the letters AT
and are followed directly (no space) by the command.
(These commands are also case-sensitive.) All AT
commands must be entered in upper case including AT,
except w##, r#, m#, q#, and z (wakeup-on-ring).
AT commands can be divided into two groups: control
commands
and
configuration
commands.
Control
commands, such as ATD, cause the modem to perform
an action (going off-hook and dialing). The value of this
type of command is changed at a particular time to
perform
a
particular
action.
For
example,
the
ATDT1234<CR> command causes the modem to go
off-hook and dial the number, 1234, via DTMF. This
action exists only during a connection attempt. No
enduring change in the modem configuration exists
after the connection or connection attempt has ended.
Configuration
commands
change
modem
characteristics until they are modified or reversed by a
subsequent configuration command or the modem is
reset. Modem configuration status can be determined
with the use of “ATSR?<CR>” where “R” is the two-
character hexadecimal address of an S-register.
A command line is defined as a string of characters
starting with AT and ending with an end-of-line
character, <CR> (13 decimal). Command lines may
contain several commands, one after another. If there
are no characters between AT and <CR>, the modem
responds with “O” after the carriage return.
5.1. Command Line Execution
The characters in a command line are executed one at
a time. Unexpected command characters are ignored,
but unexpected data characters may be interpreted
incorrectly.
After the modem has executed a command line, the
result
code
corresponding
to
the last
command
executed is returned to the terminal or host. In addition
to the “ATH” and “ATZ” commands, the commands that
warrant a response (e.g., “ATSR?” or “ATI”) must be the
last in the string and followed by a <CR>. All other
commands may be concatenated on a single line. To
echo command line characters, set the Si2401 to echo
mode using the E1 command.
All numeric arguments, including the address and value
of an S-register, are in hexidecimal format, and two
digits must always be entered.
5.2. <CR> End-Of-Line Character
This character is typed to end a command line. The
value of the <CR> character is 13 in decimal, the ASCII
carriage return character. When the <CR> character is
entered, the modem executes the commands in the
command line.
Note:
Commands that do not require a response are exe-
cuted immediately and do not need a <CR>.
Table 12. AT Command Set Summary
Command
Function
A
Answer line immediately with modem
DT#
Tone dial number
DP#
Pulse dial number
E
Local echo on/off
H0
Go on-hook (hang up modem)
H1
Go off-hook
I
Chip revision
:I
Interrupt read and clear
M
Speaker control options
O
Return online
RO
V.23 reverse
S
Read/write S-Registers
w##
Write S-Register in binary
r#
Read S-Register in binary
m#
Monitor S-Register in binary
相關PDF資料
PDF描述
1-6374518-0 C/A LC TO LC 900UM BUF 10 SM
EYM15DTKN-S288 CONN EDGECARD 30POS .156 EXTEND
REC5-4815DRWZ/H6/C CONV DC/DC 5W 18-72VIN +/-15VOUT
A3DDB-2418M IDC CABLE- AKR24B/AE24M/AKR24B
VI-JVX-EZ-S CONVERTER MOD DC/DC 5.2V 25W
相關代理商/技術參數
參數描述
SI2401FS10-EVB 功能描述:網絡開發工具 SI2401+SI3010 ISO MODEM EVAL. BOARD RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
SI2401-FSR 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI2401URT-EVB 功能描述:網絡開發工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
SI2403 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION
SI2403-FT 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*