- 您現在的位置：買賣IC網 > PDF目錄16517 > SI2401FS08-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 + SI3008 PDF資料下載
參數資料
| 型號： | SI2401FS08-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 14/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL SI2401 + SI3008 |
| 標準包裝： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 電信，數據采集裝置（DAA） |
| 已用 IC / 零件： | SI2401 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
Si2401
Rev. 1.0
21
modem transmitting at 75 bps and receiving at 1200/
600 bps.
The Si2401 supports the V.23 turnaround procedure.
This allows a modem that is transmitting at 75 bps to
initiate a “turnaround” procedure so that it can begin
transmitting data at 1200/600 bps and receiving data at
75 bps. The modem is defined as being in V.23 master
mode if it is transmitting at 75 bps, and it is defined as
being in slave mode if the modem is transmitting at
1200/600 bps. The following paragraphs give a detailed
description of the V.23 turnaround procedure.
4.7.1. Modem in Master Mode
To perform a direct turnaround once a modem
connection is established, the master host goes into
online-command-mode
by
sending
an
escape
command (Escape pin activation, TIES, or ninth bit
escape) to the master modem.
Note:
The host can initiate a turnaround only if the Si2401 is
the master.
The host then sends the ATRO command to the Si2401
to initiate a V.23 turnaround and return to the online
(data) mode.
The Si2401 then changes its carrier frequency (from
390 Hz to 1300 Hz) and waits to detect a 390 Hz carrier
for 440 ms. If the modem detects more than 40 ms of a
390 Hz carrier in a time window of 440 ms, it echoes the
“c” response character. If the modem does not detect
more than 40 ms of a 390 Hz carrier in a time window of
440 ms, it hangs up and echoes the “N” (no carrier)
character as a response.
4.7.2. Modem in Slave Mode
Configure GPIO4 as INT (SE2[7:6] [GPIO4] = 11b). The
Si2401 performs a reverse turnaround when it detects a
carrier drop longer than 20 ms. The Si2401 then
reverses (changes its carrier from 1300 Hz to 390 Hz)
and waits to detect a 1300 Hz carrier for 400 ms. If the
Si2401 detects more than 40 ms of a 1300 Hz carrier in
a time window of 400 ms, it sets the S09[7] bit, and the
next character echoed by the Si2401 is a “v”.
If the Si2401 does not detect more than 40 ms of the
1300 Hz carrier in a time window of 400 ms, it reverses
again and waits to detect a 390 Hz carrier for 440 ms.
Then, if the Si2401 detects more than 40 ms of a
390 Hz carrier in a time window of 220 ms, it sets the
S09[7] bit, and the next character echoed by the Si2401
is a “c”.
At this point, if the Si2401 does not detect more than
40 ms of the 390 Hz carrier in a time window of 440 ms,
it hangs up, sets the S09[7] bit, and the next character
echoed by the Si2401 is an “N” (no carrier).
Successful completion of a turnaround procedure in
master
or
slave
mode
automatically
updates
S07[4] (V23T) and S07[5] (V23R) to indicate the new
status of the V.23 connection.
To avoid using the INT pin, the host may also be notified
of the INT condition by using 9-bit data mode. Setting
S15[0] (NBE) = 1b and S0C[3] (9BF) = 0b configures
the ninth bit on the Si2401 TXD path to function exactly
as the INT pin has been described.
4.8. V.42 HDLC Mode
The Si2401 supports V.42 through hardware HDLC
framing in all modem data modes. Frame packing and
unpacking including opening and closing flag generation
and detection, CRC computation and checking, zero
insertion and deletion, and modem data transmission
and reception are all performed by the Si2401. V.42
error correction and V.42bis data compression must be
performed by the host.
The digital link interface in this mode uses the same
UART interface (8-bit data and 9-bit data formats) as in
the asynchronous modes, and the ninth data bit may be
used as an escape by setting S15[0] (NBE) = 1b. When
using HDLC in 9-bit data mode, if the ninth bit is not
used as an escape, it is ignored.
To use the HDLC feature on the Si2401, the host must
enable HDLC operation by setting S13[1] (HDEN) = 1b.
The host may initiate the call or answer the call using
either the “ATDT#”, the “ATA” command or the auto-
answer mode. (The auto-answer mode is implemented
by setting register S00 (NR) to a non-zero value.) When
the call is connected, a “c”, “d”, or “v” is echoed to the
host controller. The host may now send/receive data
across the UART using either the 8-bit data or 9-bit data
formats with flow control.
At this point, the Si2401 begins framing data into the
HDLC format. On the transmit side, if no data is
available from the host, the HDLC flag pattern is sent
repeatedly.
When
data
is
available,
the
Si2401
computes the CRC code throughout the frame, and the
data is sent with the HDLC zero-bit insertion algorithm.
HDLC flow control operates in a similar manner to
normal asynchronous flow control across the UART and
is shown in Figure 4. To operate flow control (using the
CTS pin to indicate when the Si2401 is ready to accept
a character), a DTE rate higher than the line rate should
be selected.
相關PDF資料 |
PDF描述 |
|---|---|
| 1-6374518-0 | C/A LC TO LC 900UM BUF 10 SM |
| EYM15DTKN-S288 | CONN EDGECARD 30POS .156 EXTEND |
| REC5-4815DRWZ/H6/C | CONV DC/DC 5W 18-72VIN +/-15VOUT |
| A3DDB-2418M | IDC CABLE- AKR24B/AE24M/AKR24B |
| VI-JVX-EZ-S | CONVERTER MOD DC/DC 5.2V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI2401FS10-EVB | 功能描述:網絡開發工具 SI2401+SI3010 ISO MODEM EVAL. BOARD RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| SI2401-FSR | 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI2401URT-EVB | 功能描述:網絡開發工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| SI2403 | 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。