參數資料
型號： SCAN182245BFMX
廠商： National Semiconductor Corporation
英文描述： Non-Inverting Transceiver with 25OHM Series Resistor Outputs
中文描述： 非反相與25OHM系列電阻器輸出
文件頁數： 11/18頁
文件大?。?/td> 231K
代理商： SCAN182245BFMX
SCAN ABT Live Insertion and Power Cycling Characteristics
SCAN ABT is intended to serve in Live Insertion backplane
applications. It provides 2nd Level Isolation
1
which indicates
that while external circuitry to control the output enable pin
is unnecessary, there may be a need to implement differen-
tial length backplane connector pins for V
CC
and GND. As
well, pre-bias circuitry for backplane pins may be necessary
to avoid capacitive loading effects during live insertion.
SCAN ABT provides control of output enable pins during
power cycling via the circuit in Figure A. It essentially con-
trols the G
n
pin until V
CC
reaches a known level.
Duringpower-up, when V
CC
ramps through the 0.0V to 0.7V
range, all internal device circuitry is inactive, leaving output
and I/O pins of the device in high impedance. From approxi-
mately 0.8V to 1.8V V
CC
, the Power-On-Reset circuitry,
(POR), in Figure A becomes active and maintains device
high impedance mode. The POR does this by providing a
low from its output that resets the flip-flop The output, Q, of
the flip-flop then goes high and disables the NOR gate from
an incidental low input on the G
n
pin. After 1.8V V
CC
, the
POR circuitry becomes inactive and ceases to control the
flip-flop. To bring the device out of high impedance, the G
n
input must receive an inactive-to-active transition, a high-to-
low transition on G
n
in this case to change the state of the
flip-flop. With a low on the Q output of the flip-flop, the NOR
gate is free to allow propagation of a G
n
signal.
During power-down, the Power-On-Reset circuitry will be-
come active and reset the flip-flop at approximately 1.8V
V
CC
. Again, the Q output of the flip-flop returns to a high and
disables the NOR gate from inputs from the G
n
pin. The
device will then remain in high impedance for the remaining
ramp down from 1.8V to 0.0V V
CC
.
Some suggestions to help the designer with live insertion
issues:
#
The G
n
pin can float during power-up until the Power-On-
Reset circuitry becomes inactive.
#
The G
n
pin can float on power-down only after the Pow-
er-On-Reset has become active.
The description of the functionality of the Power-On-Reset
circuitry can best be described in the diagram of Figure B.
TL/F/11657–19
FIGURE A
TL/F/11657–20
FIGURE B
1
Section 7, ‘‘Design Consideration for Fault Tolerant Backplanes’’, Application Note AN-881.
SCAN ABT includes additional power-on reset circuitry not otherwise included in ABT devices.
http://www.national.com
11
相關PDF資料
PDF描述
SCAN182245BSSCQB Non-Inverting Transceiver with 25OHM Series Resistor Outputs
SCAN182245BSSCX Non-Inverting Transceiver with 25OHM Series Resistor Outputs
SCAN18245T Non-Inverting Transceiver with TRI-STATE Outputs(帶三態輸出的同相收發器)
SCAN18373T Transparent Latch with TRI-STATE Outputs(帶三態輸出的透明鎖存器)
SCAN18374T D Flip-Flop with TRI-STATE Outputs(帶三態輸出的D觸發器)
相關代理商/技術參數
參數描述
SCAN182245BSSCQB 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs
SCAN182245BSSCX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs
SCAN182245BSSMQB 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs
SCAN182245BSSMX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs
SCAN182245CFCQB 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*