參數資料
型號： SC28L198A1BE,557
廠商： NXP Semiconductors
文件頁數： 24/57頁
文件大?。?/td> 0K
描述： IC UART OCTAL W/FIFO 100-LQFP
產品培訓模塊： Stand-Alone UARTs
標準包裝： 450
特點： 故障啟動位檢測
通道數： 8
FIFO's： 16 字節
電源電壓： 3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 管件
產品目錄頁面： 828 (CN2011-ZH PDF)
其它名稱： 568-1210
935262731557
SC28L198A1BE
Philips Semiconductors
Product data sheet
SC28L198
Octal UART for 3.3 V and 5 V supply voltage
2006 Aug 10
30
Table 38. I/OPCR – I/O Port Configuration Register
Bits 7:6
Bits 5:4
Bits 3:2
Bits 1:0
I/O3 control
I/O2 control
I/O1 control
I/O0 control
00 – GPI/TxC input
01 – I/OPIOR[3] output
10 – TxC16x output
11 – TxC1x output
00 – GPI/RxC input
01 – I/OPIOR[2]/RTSN *
10 – RxC1x output
11 – RxC16x output
00 – GPI input
01 – I/OPIOR[1]/RTSN *
10 – Reserved
11 – RxC1x output
00 – GPI/CTSN input
01 – I/OPIOR[0]output
10 – TxC1x output
11 – TxC16x output
* If I/OPCR(5:4) is programmed as ’01’ then the RTSN functionality
is assigned to I/O2, otherwise, this function can be implemented on
I/O1. (This allows for a lower pin count package option)
This register contains 4, 2 bit fields that set the direction and source
for each of the I/O pins associated with the channel. The I/O2
output may be RTSN if MR1[7] is set, or may signal ”end of
transmission” if MR2[5] is set.(Please see the descriptions of these
functions under the MR1 and MR2 register descriptions) If this
control bit is cleared, the pin will use the OPR[2] as a source if
I/OPCR[5:4] is b’01. The b’00 combinations are always inputs. This
register resets to x’0, effectively configuring all I/O pins as inputs on
power up or reset. Inputs may be used as RxC, TxC inputs or
CTSN and General Purpose Inputs simultaneously. All inputs are
equipped with change detectors that may be used to generate
interrupts or can be polled, as required.
NOTE: To ensure that CTSN, RTSN and an external RxC are
always available, if I/O2 is not selected as the RTSN output, the
RTSN function is automatically provided on I/O1.
GENERAL PURPOSE OUTPUT PIN CONTROL
The following four registers control the function of the GOUT0 pin.
These output pins have a unique control matrix which includes a
clocking mechanism that will allow the pin to change synchronously
with an internal or external stimulus. See diagram below.
Table 39. GPOSR – General Purpose Output
Select Register
GPOSR selects the signal or data source for the GOUT0 pin. The Tx
and Rx clock selection is straight forward. The selection of the
GPOR allows a more flexible timing control of when the GOUT0 pin
changes.
Bits 7:4
Bits 3:0
Reserved
Global General Purpose Output 0 Selection
0000 – 0111 reserved
1000 = TxC1x a
1001 = TxC16x a
1010 = RxC16x a
1011 = TxC16x b
1100 = GGPOR(3)
1101 = GGPOR(2)
1110 = GGPOR(1)
1111 = GGPOR(0)
Table 40. GPOR – General Purpose Output
Register
This register is a read/write register. Its contents may be altered by
a GPOR Write or by the GPOC and GPOD registers shown below.
The GPOD and GPOC may be programmed to cause the individual
bits of the GPOR to change synchronously with internal or external
events. The cells of this register may be thought of as a “Two Port
flip-flop”; one port is controlled by a D input and clock, the other by a
data load strobe. A read of the GPOR always returns its current
value regardless of the port from which it was loaded.
Bits 7:4
Bit 3
Bit 2
Bit 1
Bit 0
Reserved
GPOR(3)
GPOR(2)
GPOR(1)
GPOR(0)
Table 41. GPOC – General Purpose Output Clk
Register
This controls the clock source for GPOR that will clock and/or toggle
the data from the selected GPOD source. When code b’00 is
selected, no clock will be provided, thereby preventing any change
through the D port.
Bits 7:6
Bits 5:4
Bits 3:2
Bits 1:0
Clk Sel
GPOR(3)
Clk Sel
GPOR(2)
Clk Sel
GPOR(1)
Clk Sel
GPOR(0)
00 = none
01 = GIN0
10 = GIN1
11 = reserved
00 = none
01 = GIN0
10 = GIN1
11 = reserved
00 = none
01 = GIN0
10 = GIN1
11 = I/O3c
00 = none
01 = GIN0
10 = GIN1
11 = I/O3a
Table 42. GPOD – General Purpose Output Data
Register
This register selects the data that will be presented to the GPOR “D”
input. Note that selection b’10 selects the inverted GPOR data as
the input. In this case, the GPOR output will toggle synchronously
with the clock selected in the GPOC.
Bits 7:6
Bits 5:4
Bits 3:2
Bits 1:0
Data Sel
GPOR(3)
Data Sel
GPOR(2)
Data Sel
GPOR(1)
Data Sel
GPOR(0)
00 = ’1’
01 = ’0’
10 = GPOR3N
11 = reserved
00 = ’1’
01 = ’0’
10 = GPOR2N
11 = reserved
00 = ’1’
01 = ’0’
10 = GPOR1N
11 = I/O3d
00 = ’1’
01 = ’0’
10 = GPOR0N
11 = I/O3b
相關PDF資料
PDF描述
V24B5H150BF CONVERTER MOD DC/DC 5V 150W
SC28L198A1BE,528 IC UART OCTAL SOT407-1
V24B5H150BL3 CONVERTER MOD DC/DC 5V 150W
V24B5H150BL CONVERTER MOD DC/DC 5V 150W
V24B5H150B3 CONVERTER MOD DC/DC 5V 150W
相關代理商/技術參數
參數描述
SC28L198A1BE-S 功能描述:UART 接口集成電路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198C1A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Octal UART for 3.3V and 5V supply voltage
SC28L201 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3.3 V, 5 V UART, 3.125 Mbit/s, with 256-byte FIFO
SC28L201A1DGG 功能描述:UART 接口集成電路 3-5V 1CH UART 3MBPS 256B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L201A1DGG,112 功能描述:UART 接口集成電路 3-5V 1CH UART 3MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*