- 您現在的位置：買賣IC網 > PDF目錄374721 > SC2441EVB (Semtech Corporation) Very Low Input Voltage 2-Phase Synchronous Step-down Controllers with Step-up Converter PDF資料下載
參數資料
| 型號： | SC2441EVB |
| 廠商： | Semtech Corporation |
| 英文描述： | Very Low Input Voltage 2-Phase Synchronous Step-down Controllers with Step-up Converter |
| 中文描述： | 非常低的輸入電壓2相同步降壓與升壓轉換器控制器 |
| 文件頁數： | 13/35頁 |
| 文件大?。?/td> | 733K |
| 代理商： | SC2441EVB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
13
2005 Semtech Corp.
www.semtech.com
POWER MANAGEMENT
Applications Information
SC2441
The SC2441 consists of two current-mode synchronous
buck controllers and an auxiliary boost converter. The
SC2441 can be used to generate
1) two independent step-down outputs or
2) dual phase single output with current sharing and
3) a step-up output
The application information using SC2441 for the control
of step-down and step-up converters are described below.
Step-down Converter
Specifications of a step-down converter are given by the
followings
Input voltage range:
V
[
V
in
Input voltage ripple (peak-to-peak):
V
in
Output voltage:
V
Output voltage accuracy:
ε
Output voltage ripple (peak-to-peak):
V
o
Nominal output (load) current:
I
o
Maximum output current limit:
I
Output (load) current transient slew rate:
dI
o
(A/s)
Circuit efficiency:
η.
]
V
,
max
,
in
min
,
in
∈
Based on these converter specifications, selection criteria
and design procedures for the following components are
described.
1) output inductor (
L
) type and value,
2) output capacitor (
C
) type and value,
3) input capacitor (
C
) type and value,
4) power switch MOSFET’s,
5) current sensing and limiting circuitry,
6) voltage sensing circuitry,
7) loop compensation circuitry.
To illustrate the design process, the following example is
used:
V
in
=3.3V, V
o
=1.2V, I
o
=4A, f
s
=500kHz.
Operating Frequency (f
s
)
The switching frequency in the SC2441 is user-
programmable. The advantages of constant frequency
operation are simple passive component selection and fast
transient response with simple frequency compensation.
Before setting the operating frequency, the following trade-
offs should be considered.
1) passive component sizes
2) converter efficiency
3) EMI
4) Minimum switch on time and
5) Maximum duty ratio
For a given output power, the sizes of the passive
components are inversely proportional to the switching
frequency, whereas MOSFET’s/Diodes switching losses are
proportional to the operating frequency. Other issues such
as heat dissipation, packaging and the cost issues are
also to be considered. The frequency bands for signal
transmission should be avoided because of EM
interference.
Minimum Switch On Time Limitation
In both step-down controllers, the falling edge of the
clock turns on the top MOSFET. The inductor current
ramps up so does the sensed voltage. After the sensed
voltage crosses a threshold determined by the error
amplifier output, the top MOSFET is turned off. The
propagation delay time from the turn-on of the controlling
FET to its turn-off is the minimum switch on time. The
SC2441 has a minimum on time of about 180ns at room
temperature. This is the shortest on interval of the
controlling FET. The controller either does not turn on the
top MOSFET at all or turns it on for at least 180ns.
For a synchronous step-down converter, the operating
duty cycle is
Vo
/
VIN
. So the required on time for the top
MOSFET is
Vo
/(
VIN f
)
. If the frequency is set such that
the required pulse width is less than 180ns, then the
converter will start skipping cycles. Due to minimum on
time limitation, simultaneously operating at very high
switching frequency and very short duty cycle is not
practical. If the input voltage is 3.3V and the operating
frequency is 1MHz, the lowest output voltage will be 0.6V.
There will not be enough modulation headroom if the on
time is simply made equal to the minimum on time of the
SC2441. For ease of control, we recommend the required
pulse width to be at least 1.5 times the minimum on time.
Maximum Duty-cycle Consideration
When operating at 500KHz, the maximum top MOSFET
on duty-cycle is 90%. The top MOSFET therefore turns off
for at least 200ns every cycle regardless of the switching
frequency. This places an upper bound on the voltage
相關PDF資料 |
PDF描述 |
|---|---|
| SC2441ITSTRT | Very Low Input Voltage 2-Phase Synchronous Step-down Controllers with Step-up Converter |
| SC2442 | High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2442H | High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2442HITSTR | High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2442HITSTRT | High Performance Wide Input Range Dual Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC2441ITSTRT | 制造商:Semtech Corporation 功能描述:Controller IC |
| SC2442 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2442H | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Wide Input Range Dual Synchronous Buck Controller |
| SC2442HITSTR | 制造商:Semtech Corporation 功能描述: |
| SC2442HITSTRT | 制造商:Semtech Corporation 功能描述:Controller IC |
發布緊急采購，3分鐘左右您將得到回復。